Related Manuals for EVO Gimbals Rage Gen.2
Summary of Contents for EVO Gimbals Rage Gen.2
- Page 1 English Manual v2.0 20810 Sockeye Pl #200 Bend, OR 97701 Support and Sales Questions: Tel: (866) 977-6688 Monday to Friday 9AM to 5PM Pacific Time or email support@evogimbals.com EVOGimbals.com...
-
Page 3: Table Of Contents
CONTENTS Packing List Disclaimer and Warning Get to Know The EVO RAGE Gen2 Preparing and Charging the Batteries Camera Installation Balance Adjustment Gimbal Controls Start Up Gimbal Control Modes Calibration Firmware Upgrade & Panasonic CCI Cable SONY CCI Cable App Operation Product Specifications Motor Power Settings Warranty... -
Page 4: Packing List
EVO RAGE Gen2 Gimbal Camera Mount Screw EVO Gimbals reserves the right of final explanation for this document and all relevant documents relating to the RAGE Gen2, and the right to make changes at any time without notice. Please visit EVOGimbals.com for the latest product information. - Page 5 4. Never use non-EVO Gimbals batteries. If replacement or backup is needed, please purchase new batteries from EVO Gimbals' official website or authorized channels. EVO Gimbals takes no responsibility for any damage caused by non-EVO Gimbals batteries.
- Page 6 1. Dispose the battery in a specific recycling area only after a complete discharge. Do not throw away the 1. Do not attach the batteries to a wall outlet or car charger socket directly. Always use a EVO Gimbals battery in regular trash containers. Strictly follow your local regulations regarding the disposal and recycling approved adapter for charging.
-
Page 7: Get To Know The Evo Rage Gen2
Camera is not included in product package, and shall be bought separately.The depictions provided herein are for reference only. Please use and charge batteries provided or approved by EVO Gimbals only. EVO Gimbals will not take any responsibility for explosion, fire and/or accidents caused by non-EVO batteries. -
Page 8: Camera Installation
OPERATION OVERVIEW CAMERA INSTALLATION Operating Methods Mount The Camera There are two main operating positions used when shooting video with the EVO Rage Gen2 - Normal & Inverted. The inverted position requires that you properly balance your gimbal so that the handle does not hit the camera while switching between Normal to Inverted. -
Page 9: Balance Adjustment
BALANCE ADJUSTMENT BALANCE ADJUSTMENT Balance Adjustment on The Tilt Axis Step Three: Step One: Loosen Tilt Motor thumb screw . Adjust the After camera is mounted to the mounting plate, balance by sliding the Tilt Axis Arm until the loosen the thumb screw lever underneath the camera stays vertically balanced while pointing mounting plate to allow forward and backward sliding of the plate. -
Page 10: Gimbal Controls
BALANCE ADJUSTMENT GIMBAL CONTROLS Balance Adjustment on The Pan Axis Battery Level Joystick Battery Level Indicator When powered on you will see quick yellow flashes for MODE 3 seconds and then solid yellow for 1 second. Once fully Power On/Off powered the light will turn blue and flash to indicate battery level. -
Page 11: Start Up
START UP GIMBAL STABILIZATION MODES Pan Follow Mode Pan Follow Mode Pan Follow Mode Pan Follow Mode Battery Installation Unscrew the end cap, then install the One Click One Click Two Clicks One Click Three Clicks One Click two 26500 Li-ion batteries. To ensure proper ground be sure to tighten the end cap completely after battery installation, or the stabilizer will not turn... -
Page 12: Calibration
CALIBRATION CALIBRATION When do you need to calibrate the stabilizer? Six—Side Calibration Please calibrate the stabilizer when necessary to ensure normal use. Please use either method described below. When… Method One Method Two a) Slight deviation is found in the tilt angle of the camera in level position after startup. Start Up b) Slight deviation is found in the roll angle of the camera in level position after startup. -
Page 13: Firmware Upgrade & Panasonic Cci Cable
SONY CCI CABLE FIRMWARE UPGRADE & PANASONIC CCI CABLE Firmware Update SONY CCI Cable Instructions Firmware Update... Make sure the batteries have been properly installed before upgrade. With the SONY RX Series, H Series, QX Series and all Series ILDC’s you can control the shutter, zoom, CCI Cable connection points Connect the RAGE Gen2 to your computer via Micro USB cable for the firmware upgrade and calibration. -
Page 14: App Operation
APP OPERATION APP OPERATION Main Features of the APP EVO Gimbals Remote App Download Download the EVO Gimbals Remote App from either the Apple App Store or Google Play. Calibration Screen: Calibration is required when deviations are found in the 3 axes and the... -
Page 15: Product Specifications
PRODUCT SPECIFICATIONS MOTOR POWER SETTINGS Adjusting the power of the gimbal motors can be done using the EVO App or the Desktop Calibration Tool Standard Remarks Using the EVO App, select the PTZ icon (in yellow) and Input Voltage 6.8V 8.4V 12.6V scroll down to the More section. -
Page 16: Warranty
DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. Labor: For a period of one (1) year from the original date of purchase of the product (“Labor Warranty”), EVO Gimbals will, DURATION OF IMPLIED WARRANTIES: EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED at its option, repair or replace with new or refurbished product, product determined to be defective. -
Page 17: Notes
NOTES NOTES...
Need help?
Do you have a question about the Rage Gen.2 and is the answer not in the manual?
Questions and answers