Newtec M6100 Quick Start Manual

QUICk stArt GUIDE
Box Content
Item
Device
slider kit
Power Cable
QDr-report
soft Copy Documentation
Hard Copy Documentation (optional)
Slider Kit Content
Material in the box
1x LEFT
A
1x RIGHT
B
2x 2x 4x 2x 10x
D E F G
C
Safety & Cautions
Please read the safety & Cautions section of the User Manual
!
(available on www.newtec.eu/support/documentation)
before you install and use this equipment.
Rack Mounting Instructions
M6100
MDM6100
MDM6000
MCD6000
these instructions are
valid for a standard
!
19" rack, using 3
mounting holes per
rack unit (1U).
INstAll tHE slIDErs AND
DEvICE INto tHE rACk
Quantity
1
1
2
1
1
1
1
• Mount the rear of the sliders onto
the rack using a Pozi screwdriver
N° 3, using the rack mount screws
(I) and washers (H).
Required tools
• Hex Key size n°3
4
• Hex Key size n°4
• Pozi screwdriver
Size 3 (min size 2)
• Place and fix the sliding wheels
(D) with two socket cap screws (E)
on the left and right rear of the
device by using a hex key N° 3.
8x
8x
H I
6
• Place the sliding wheels onto the
sliders and slide the device into
the rack.
Configure your Device
1
• Insert cage nuts (G) into the rack, six
on the front and four on the rear of
the rack.
• Mount the front of the sliders
(A & B) onto the rack with sunk head
screws (F), using a hex key N° 4.
3
• Fix the length of the sliders by
using a hex key N° 3.
sEt DAtE AND tIME
5
CoNFIGUrE AND sAvE
• Mount the support bracket (C)
on the left and right front of
You can configure settings using the Front Panel, the Graphical User
the device with two socket cap
Interface (GUI) or the Command line Interface (ClI).
screws (E) using a hex key N° 3.
7
• Mount the brackets onto the rack
by slightly lifting the device and
to configure and save settings via GUI and ClI, please refer to
inserting the remaining screws
www.newtec.eu/support/documentation
(H & I) using a Pozi screwdriver N° 3.
sEt tHE MANAGEMENt IP ADDrEss
Display
soft Buttons
• Insert the power cable to start the device.
the only way to shut down the device is to disconnect
the power cable from the power connector. therefore
!
make sure that the power cable is accessible and not
obstructed when the device is operational.
• Wait for the menu tree to display.
• select Mgmt Itf from the corresponding soft button.
• Navigate to IP Address.
• Press OK (to unfold the branch).
• Navigate to Mgmt1.
• Press OK.
• Navigate to IP Address/prefix and press OK.
• Use the Soft Buttons to enter a new IP Address/prefix.
• Press OK to confirm the setting.
• Now connect the Ethernet cable to Mgmt1 on the back panel.
• Now you can access the device from a management PC.
• select Device from the corresponding soft button.
• Navigate to Date and Time.
• Press ok (to unfold the branch).
• Navigate to Date or Time and press OK.
• Use the navigation down button to display numerical values.
• Use the Soft Buttons to enter a new Date or time.
• Press OK to confirm the settings.
!
Please save to fix your configured settings.
to save settings via the Front Panel:
• Use the soft Button Arrow and navigate completely to the right of
the root menu pane and select Actions.
• Navigate to Device Configuration Save and press OK.
• select the configuration file name and Press OK to save the
configuration.
Navigate Buttons
Escape ok