Before Operation
Note:
1. The lock is equipped with three mechanical keys for manual lock operation. Remove mechanical keys from
the package and keep them in a safe place.
2. To power the lock, four alkaline AA batteries (not included) are required. The lock has low battery voltage
alarm (Red LED flashes and six beeps when you active the lock) to prompt replace battery. Non-alkaline and
rechargeable batteries ARE NOT RECOMMENDED.
3. By Default, the lock is configured to grant ANY fingerprint access to unlock.
4. By Default, the lock is configured can not read ID card. Please refer to RFID Card Function to enable card
reading function.
5. Please avoid strong light direct to the lock.
Structure
-1-
User Operation
User Introduction
Administrator
This will normally be an official in the company or the host of a
family who will have administrator permissions and will be able to
do various operations.
The lock can set 4 administrators and ID will be 96--99.
Normal user
This will be a user under administrator's management who will
be granted access to open the lock. The lock can set 95 normal
users and ID number will be 01--95.
The Nixie tube prompting characters
Character
--
Activation status.
Ad
Need administrator identification.
FP
AL
Delete all the users.
01-95
ID range for normal users. (95 users capacity)
96-99
ID range for administrators.(4 administrators capacity)
The Buzzer status
Status
Buzzer
Three Beeps
1
2
Two Beeps
3
Long Voice
4
Short music voice
5
Six beeps
The LED status
Status
LED
1
Bule LED flashes
2
Bule LED fast flashing
3
Red LED flashes
4
Red LED fast flashing
5
Bule and Red LED flashes
6
Red LED light
-2-
Quick Operation Mode
Register User
(
Register user without administrator.
1
Remove the battery box cover.
Press any key to activate the
lock.
5
Place one user finger twice
on the fingerprint sensor or
swipe card on the card area
twice.
-3-
Delete User
(
Delete user without administrator.
1
Remove the battery box cover.
Press any key to activate the
lock.
If "FP" selected, Press
key need to place finger twice on the sensor
OK
or swipe card twice to delete. Press
users or press
key to exit delete status.
C
If "AL" selected, Press
key after six beeps form the lock all of the
OK
normal users will be delete. The lock will auto logout deletion status.
If "ID" selected, press
to delete the appointed user. Press
OK
exit delete status or press
and
delete the appointed user.
-4-
Before Connecting, operating or adjusting this product, please read the instructions completely.
Keep this manual you will need it again.
is registered trademark of Anviz Global Inc. in the United States and other countries. It cannot be used without the
permission of Anviz.
1
1
2
2
3
4
3
5
6
4
7
8
9
10
11
5
12
13
14
15
6
16
16
7
Description
Description
The lock under initial states and be activated.
Enable or Diable work mode.
Finger or Card Verification failed.
Operation succeedful.
Delete all the user / low battery voltage alarm.
Description
Activation status.
Place same finger or swipe same card again.
Delete user status / low battery voltage alarm.
Place same finger or swipe same card again to delete.
Need administrator verify.
Unregistered finger or card .
)
2
The Nixie tube shows "--".
6
Next ID number will be
displayed after successful
registration.
Press
to continue register
OK
user or press
key to exit
C
register status.
)
2
The Nixie tube shows "--".
5
key to continue delete other
OK
key to
C
key to continue select ID number
User Manual
L100D II/L100II
Home & Business Smart Lock
LED indicator
Fingerprint sensor
Card area
Mechanical key hole
Restart button
Rubber key cover
9V emergency power terminal
Battery box cover
Battery area
Add key
Delete key
Nixie tube
"OK" Confirm Key
"C" Cancel Key
Factory Debug Port
Mechanical key
RFID Card Function
RFID Card Function: Enable this function the lock can read ID cards.
The battery lifespan can be doubled after disabling the RFID Card
Function.
Enable: Verify any registered fingerprint on lock and press
Disable: Verify any registered fingerprint on lock and press
Normal Open Function
Normal open function: Open the door without fingerprint or card
verification on the lock, which is fit for meeting room and some
places free to in or out.
Enable: Verify any registered fingerprints or cards on lock and
press
key.
OK
Disable: Press
key directly.
C
Initialize The Fingerprint Lock
Initializing the fingerprint lock means all of the user will be deleted
and back to factory mode.
Operation:
The Initialization Button is in the inside panel of the lock, and holding the
Initialization Button until the lock prompts the voice of initialization.
When initialization is completed, the fingerprint lock will restart automaticly.
Note: Fingerprint Lock Initialization must be supplied with power.
-
3
Pressing
key.
* Note:
One ID only can register one fingerprint or one card.
-
3
Pressing
key.
Place finger:
Place finger in the center of the sensor.
Place finger flat on the sensor surface.
8
9
10
11
12
15
4
The Nixie tube will display
normal user ID: 01. Please
press
and
key to select
and press
to enter the
OK
registration status.
(User ID range is 01-95)
4
When the Nixie tube flashes,
please press
and
key to
select "FP", "AL" or "ID"
number and press
.
OK
(V2.1)
13
14
key.
key.
Need help?
Do you have a question about the L100D II and is the answer not in the manual?
Questions and answers