Advertisement
Quick Links
BL100 Installation Guide
Ⅰ Reference Tools for Installing the Door Lock
.
1 Hammer
2 Screwdriver
3 Chisel for wood working
6 Hole saw
7 Polisher
Ⅱ
. Quick Reference
A. Quick reference for Installation Guide
Ø
Confirm the door information before installation, please see
installation;
Install Lock Body, please see Ⅳ. Install Lock Body;
Ø
Confirm the length of Locking Bar, please see Ⅴ. Confirm the length of Locking Bar;
Ø
Install the Front panel Assembly, please see Ⅵ. Install the Front panel Assembly;
Ø
Install Batteries, please see Ⅶ. Install the Batteries;
Ø
Ø
Install the Rear panel Assembly, please see Ⅷ. Install the Rear panel Assembly;
Use Instruction, please see Ⅸ. Use Instructions;
Ø
Ø
The Basic Operation, please seeⅩ. The Basic Operation;
Ø
Ⅺ. Routine Maintenance
Routine Maintenance, please see
4 Angle square
Percussion drill
5
8 Rivet gun
9 Carpenter's pencil
10 Pliers
Ⅲ. Confirm the door information before
.
1
B. List of Lock Accessories
Keyhole
1
Version: V1.0
Cover
Date: 2012.3.16
Front panel
2
Assembly
Silica gel
3
backing plate
4
Lock body
Back Lining
5
Plate
Ⅲ Confirm the door information before installation
.
1. Installation Requirements
This fingerprint lock is not configured with a handle, and the user can install it on the door as desired. The
fingerprint lock is applicable to doors of 3550 mm in thickness.
2. Make sure of the door opening directions and lock body directions
(1). Make sure of the door opening directions. The lock body's outside and inside can't be set contrary. Assume
you are standing outside and facing a door and then there are four door opening directions: Left inward, left
outward, right inward and right outward. Left inward/outward means the door swings inward/outward with
hinges on the left; right inward/outward means the door swings inward/outward with hinges on the right, as
shown in the following Figure 1:
(2). Make sure of the lock body directions. According to the door opening directions to make sure of the lock
body directions, shown as the following Figure 2:
6
Screw (4 PCS)
4 PCS AA
7
Batteries
Rear panel
8
assembly
9
Screw (2PCS)
10
Key (2PCS)
2
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Anviz bl100
Summary of Contents for Anviz bl100
- Page 1 B. List of Lock Accessories BL100 Installation Guide Keyhole 1 6 Screw (4 PCS) Version: V1.0 Cover Date: 2012.3.16 Front panel 4 PCS AA 2 7 Assembly Batteries Ⅰ Reference Tools for Installing the Door Lock . Silica gel Rear panel 3 8 backing plate assembly 4 Lock body 9 Screw (2PCS) 1 Hammer 2 Screwdriver 3 Chisel for wood working 4 Angle square Percussion drill 5 Back Lining 5 10 Key (2PCS) ...
- Page 2 Ⅳ. Install Lock Body 1. Determine the installation height and installation location; stick the holedrilling template to an appropriate location according to the dooropening mode, as shown in Figure 41. 2. Insert the Lock Body into the matching Hole Slot. as shown in Figure 5: Note: There has a "•UP" flag on the Lock Body. Before installing the Lock Body, confirm how to install it based on the tip flag. Figure 1 Figure 2 (3). To set the lock as "Left Open" or "Right Open" on the Rear panel Assembly, shown as Figure 3: Figure 41 ...
- Page 3 3. After the procedure is completed, fix the Lock Body using a screwdriver, as shown in Figure 6. Insert the Ⅵ. Install the Front panel Assembly screwdriver into the crossshaped hole of the Lock Body. When you rotate the cylinder clockwise, it springs out automatically, as shown in Figure 7. When you rotate the cylinder counterclockwise, it springs back automatically, 1. Install a Silica gel backing plate on the f Front panel Assembly (moisture proof / waterproof). As shown in as shown in Figure 8. ...
- Page 4 3. Cover the Silica gel Backing Plate onto the Rear panel Assembly, turn the Lock Button to make the Hole Slot Ⅶ. Install the Batteries vertical to the ground, and insert Locking Bar into the Hole Slot, as shown in Figure 19. In this case, when you 1. Prepare four AA batteries. You are advised to use new batteries with the same brand. turn the Lock Button, the bolt can sprung out or back automatically. 2. Put batteries into the Rear panel Assembly properly. As shown in Figure 161 and 162: AA batteries Rear panel Assembly Figure 20 Figure 19 Figure 162 Figure 161 4. Push the Rear panel Assembly ahead to ensure that it can cover the whole Back Lining Plate. Install screws and fix them using a screwdriver. As shown in Figure 20. Ⅷ. Install the Rear panel Assembly Ⅸ Use Instructions . 1.
- Page 5 You must modify the Master Pass Code (MPC). The lock can be used normally only after the User ID of an administrator is entered. If the MPC is not modified, the other functions of the system except for the initialization system are not available in the management mode. If no administrator is registered, ordinary users cannot also be registered. Note: The method and step of change Master Pass Code, Enroll Administrator and Enroll Ordinary user, please see BL100 Fingerprint Lock User Manual. (2). Do not remove batteries when matching, enrolling or deleting fingerprints because the sudden powerdown may result in data loss of fingerprint locks. Prior to removing batteries, make sure the fingerprint lock is not in working state. (3). It is recommended to replace the fingerprint lock batteries at least once every six months to avoid damaging the ...
- Page 6 Ⅲ. Enroll an Ordinary User key to confirm. Enter the new 3. Press "5" key on the lock and enter the new 5 digits MPC, then press the Ø Enroll a Fingerprint Ordinary User MPC once again then press the key to confirm. Once you hear 1 long beep and the key flashes green, namely you have successfully changed the MPC code. 1. Press key to start the lock and enter the Verify State. Ⅱ Enroll an Administrator . 2. There have two methods to enter the Management Mode: ① Press and hold the key until you hear 1 long 1. Press key to start lock, and then enter the Verify State. beep, enter the 5 digits MPC, and then press key to enter the Management Mode. ② Verify the registered administrator's password and fingerprint to enter the Management Mode. key until you hear 1 long beep, enter the 5 digits MPC, and then press key to 2. Press and hold the ...
- Page 7 key will light for 3s, then the key to confirm, then input "000" again and press key to confirm. The buzzer (2) If verification failed. The buzzer will give two short beeps, the red LED at 3. Input "000" and press green LED will flash, the user can use fingerprint to verify again until verify successful. will give a long beep, the key flash green light, namely successful delete all users. Ø The Password Verification Notice: The operation can only delete ordinary users. If you want to delete administrator, you should do reset 1. Press key to start the lock and enter the Verify State. operation. 2. Press number key of lock to input the correct 4 digits password, and press key to confirm. (1) If the password is correct, then verify successful, the buzzer will give a long beep and unlock automatic, the Ⅺ. Routine Maintenance green LED at Fingerprint Collector will put out, the Green LED at key will light for 3s, at this moment you 1. The lock surface is forbidden to contact corrosive substances. Otherwise, the protective layer of the lock surface can press the key to lock. (2) If the password is wrong, then the verification failed. The buzzer will give two short beeps, the RED LED at may be damaged, and therefore the glossiness of the lock surface may be decreased. To keep the lock surface glossy, ...
Need help?
Do you have a question about the bl100 and is the answer not in the manual?
Questions and answers