Sleep Timer; Troubleshooting - RCA RCR412S User Manual

RCR412S_NA_IB_REVA.qxd
Sleep Timer (continued)
!
TIP: Any keypress other than the number keys is ignored. If you
don't enter the sleep time within 10 seconds after pressing the SLEEP
key, you must start over at step 1. The illuminated ON·OFF key blinks
four times and then turns off, indicating your attempt to program the
Sleep Timer has been unsuccessful.
6. The Sleep Timer is now set.
7. Leave remote aimed at the TV. Once the Sleep Timer is set, you
can continue to use the remote without affecting the Sleep Timer.
However, because the timing mechanism for the Sleep Timer is built
into the remote itself, the remote must be in TV Mode and pointed
at the TV to activate the Sleep Timer.
Note: If the ON·OFF key is pressed, the Sleep Timer is canceled.

Troubleshooting

Problem: The remote does not operate your component.
• You must put the remote in the correct mode by pressing
the corresponding component key (TV, DVD, VCR·AUX, SAT·CBL)
so the remote knows which component you want to operate.
• Remove any obstacles between the remote and the component.
Make sure to aim the remote at the IR sensor on the component.
• Make sure the batteries are fresh and are properly installed. (See
Battery Installation on page 3.) Replace the batteries with two new
AA batteries, if necessary. Reprogramming may be required.
• Reset the remote. Remove the batteries, then press and hold the
number 1 key on the remote for several seconds to reset the
microprocessor inside the remote. Release the number 1 key,
reinstall the batteries, and press the ON·OFF key. If it lights up,
reprogram the remote and try again. If it doesn't light up, replace
the batteries with new ones.
Problem: The remote can't be programmed to operate
your component.
• If you are testing the remote after you have entered the code, you
may be too far away from the component or at a wrong angle. This
remote uses IR (infrared) technology to communicate with
components. The remote sends the code, and the component's IR
sensor reads the code. Therefore, there must be an unobstructed
path between the remote and the IR sensor on the component.
Move closer and make sure you point the remote at the component
(DVD player when programming the DVD key; TV when
programming the TV key; satellite or cable box when programming
the SAT·CBL key, VCR or auxiliary component when programming
the VCR·AUX key).
• If you've used the Direct Entry programming methods to enter the
codes for your brand and the unit is still not functioning properly,
try one of the Code Search methods. (See pages 4-9.)
• To control combo units, like TV/VCRs, TV/DVDs or
TV/VCR/DVDs, you must program the individual corresponding
component keys to control each part of the combo unit. Once
programmed successfully, the TV key controls the TV functions, and
the VCR·AUX or DVD key controls the VCR or DVD functions,
respectively. There is a specific section in the Code Lists for combo
units. The codes in this section should be tried first using Direct
Code Entry on the TV and DVD or VCR·AUX keys. If this is
unsuccessful, follow the normal programming methods for both the
TV and the DVD or VCR·AUX keys.
• Make sure the batteries are fresh and are properly installed.
Problem: The remote is not performing commands properly.
• You must put the remote in the correct mode by pressing
the corresponding component key (TV, DVD, VCR·AUX, SAT·CBL)
so the remote knows which component you want to operate.
• Make sure component is "ready" (e.g., DVD player has disc loaded;
VCR has tape loaded, etc.)
• You may have pressed an invalid key for the mode the remote is in.
12
5/21/04 1:03 PM Page 12
• If you're trying to turn on an RCA, GE or PROSCAN component,
press the component key (TV, DVD, VCR·AUX, SAT·CBL) instead
of the ON·OFF key.
• If you're trying to change channels, try pressing the OK key after
entering the channel number as this is a requirement of certain
models and brands.
• There is a possibility that a programmed code may only be able
to control some of your component features (e.g., only turns a
component on and off). To confirm that the component key is
programmed with the correct code for maximum functionality,
test the component. Attempt to control a variety of the component's
functions with the remote. If some of the features of your
components do not work, try programming the remote with a
different code in the list using the Direct Code Entry Method, until
you find the code that allows the remote to control the majority of
your component's functions. Different codes can provide different
levels of functionality.
Problem: The illuminated ON·OFF key does not light when you
press a key.
• You may have pressed an invalid key for the mode the remote
is in. You must put the remote in the correct mode by pressing
the corresponding component key (TV, DVD, VCR·AUX, SAT·CBL)
so the remote knows which component you want to operate.
• Make sure the batteries are fresh and are properly installed. (See
Battery Installation on page 3.) Replace the batteries with two new
AA batteries, if necessary. Reprogramming may be required.
Problem: The VCR won't record.
• Make sure the remote is in VCR Mode.
• Make sure the tape is properly loaded in the VCR.
• Make sure the tape is not write-protected. If the safety tab is removed
the tape is write-protected, and you cannot record onto that tape.
Problem: The remote will not change channels on component.
• You must put the remote in the correct mode by pressing
the corresponding component key (TV, DVD, VCR·AUX, SAT·CBL)
so the remote knows which component you want to operate.
• Press the OK key after you enter a channel number.
• Remove any obstacles between the remote and the component.
Make sure to aim the remote at the IR sensor on the component.
Problem: The component's menu does not appear on the TV screen.
• Make sure you have connected your component to your TV properly
and selected the correct input. (See your components' Owner's
Manuals for proper connection procedures.)
• You must put the remote in the correct mode by pressing
the corresponding component key (TV, DVD, VCR·AUX, SAT·CBL)
so the remote knows which component you want to operate.
• Menu access isn't supported for all brands. If that's the case, you'll
need to use your original remote control to access menu functions for
these components.
For more information, please visit www.rca.com.
13