Advertisement
Table of Contents
Sales +44 (0) 8700 766900
Technical +44 (0) 8700 766902
Salus Controls plc
Enterprise Park, Bala
Gwynedd, LL23 7NL
Regional offices, England & Scotland.
Web: www.salus-tech.com
Email: sales@salus-tech.com
Maintaining a policy of continual product
development Salus Controls plc. reserve the right to
change specification, design and materials of
products listed in this brochure without prior notice.
Manual Issue No. IM-EP101-001
In st ru ct io n M a nu al
Single Channel
PROGRAMMER
Model No:- EP101 230V / Volt Free
Selectable
Thank you for purchasing this Salus product
- if installing for someone else, please ensure that
the instructions are handed to the householder.
Warning - Please read this manual prior to
installation or use.
Shock Hazard
This unit must be installed by a competent person,
in accordance with BS 7671 (the IEE Wiring
Regulations), or other relevant national regulations
and codes of good practice.
Always isolate the AC Mains supply before removing
the unit from the Industry Standard Back Plate.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Salus EP101
Summary of Contents for Salus EP101
- Page 1 In st ru ct io n M a nu al Single Channel PROGRAMMER Model No:- EP101 230V / Volt Free Selectable Sales +44 (0) 8700 766900 Technical +44 (0) 8700 766902 Thank you for purchasing this Salus product - if installing for someone else, please ensure that the instructions are handed to the householder.
- Page 2 FFL. The EP101 is easily installed using the Industry these jumpers are found on the rear of the unit. 2) Isolate AC mains supply, no Standard back plate supplied which can be Always enable the internal Back Up Battery Vac and fused at 6 amps.
- Page 3 Back Plate & Wiring for the EP101 Terminals: User Instructions for E pers: 1) Select a suitable location noting the advice in page 1 For 230V Switching Initial power up of your E select the jumper positions of this manual, a suitable mounting height is 1.5m •...
-
Page 4: Setting The Clock
"12 hr" or "24 hr" format. tching Initial power up of your EP101 Same for both 5-2 and 7 days program. • Press SELECT, clock and "SET" are displaye • After power up or RESET is pressed, the "Hour"... -
Page 5: Daylight Saving
t Program Settings after reset. • Release SET and SELECT, press to toggle • Press and release SELECT to set the Day of Month, Day Light Saving between "12 hr" or "24 hr" format. "d xx" is displayed, press to increase or or both 5-2 and 7 days program. - Page 6 nd release SELECT to set the Day of Month, • Press SELECT at any time to confirm the selection. Day Light Saving 7 days program selec s displayed, press to increase or "Hour" is flashing to indicate that it is the selected When enabled, the clock will automatically shift 1 •...
-
Page 7: Operating Mode Selection
ny time to confirm the selection. • Selected item will be flashing and can be a 7 days program selected o indicate that it is the selected key. Program time is changed • To review or change program, press SET in Normal minutes steps. -
Page 8: Temporary Override
The selected item will flash again once the AUTO Automatic program control d or adjusted with the below sequences. key is released. For EP101, +1Hr is pressed Continuously off m 1 ON) "hour" "minute" • Programmer will return to normal mode after 15... - Page 9 • When the +1Hr Program Override mode is activated tomatic program control adjust. and the clock is displayed, pressing of +1Hr will For EP101, +1Hr is pressed ntinuously off review the current settings with the "SET" displayed, to activate the +1Hr Program with no change to the internal count down timer(s).
-
Page 10: Lcd Backlight
ff at Holiday Override LCD Backlight: ion, • Press and hold BL/HOLIDAY at normal mode • LCD backlight is activated when BL/HOLIDAY or any for 3 seconds to activate the Holiday Override key is pressed. The backlight will automatically turn off disappear.
Need help?
Do you have a question about the EP101 and is the answer not in the manual?
Questions and answers