Related Manuals for Olympus Delta
Summary of Contents for Olympus Delta
-
Page 1: Quick Start Guide
DELTA Portable Workstation Quick Start Guide International version 103158-01EN [U8998465]— Revision A April 2012... -
Page 2: Table Of Contents
An A020-D test stand (U8990865) • Any DELTA handheld analyzer model (including the Premium, Standard, or Classic) In this configuration, the DELTA is controlled by the Olympus DELTA PC software. The open-beam handheld analyzer is then converted into a safe closed-beam workstation. Test stand Component Key DELTA Portable Workstation —... -
Page 3: Safety Information
2. Safety Information Radiation Safety Information The DELTA Portable Workstation is a secure and dependable system when used in accordance with recommended testing techniques and safety procedures. The radiation detected in the area outside the closed workstation is below the prescribed limit for unrestricted areas. - Page 4 Figure 2-1 Caution radiation label on top of test stand Safety Interlock Structure This mandatory feature ensures that the DELTA Portable Workstation functions as a closed-beam X-ray system. To establish a radiation-safe test chamber, the lid must be completely closed over the test platform. Until this condition is met, no test analysis or Cal Check procedures can be initiated.
-
Page 5: Physical Planning
Workstation Footprint The DELTA Portable Workstation weighs 8.9 kg (19.6 lb) with the probe adaptor, analyzer, and battery included. To make a minimum footprint for the test stand, add at least 5.1 cm (2 in.) to the actual 52.1 cm (20.5 in.) width and 37.5 cm (14.75 in.) depth. -
Page 6: Unfolding The Test Stand
You can use either the removable Li-ion battery (standard) or an AC adaptor (optional). You may also want to use the DELTA docking station or a standard battery charger in the workstation area. Both of the charging accessories require an AC power source. - Page 7 103158-01EN [U8998465], Rev. A, April 2012 Locking lever in the release position Locking lever in the release position Figure 4-1 Folded test stand Swing the left legs out to their fully extended position. Lock the legs into place using the two locking levers (see Figure 4-2 on page 7). Locking lever in the locked position Locking lever in the release position Figure 4-2 Legs locked into position...
-
Page 8: Configuring The Workstation
Thumbscrews 16-pin connector Figure 5-1 Probe adaptor Make sure that the DELTA measurement window is flush with the probe-adaptor faceplate (see Figure 5-2 on page 8). Probe-adaptor faceplate DELTA measurement window Figure 5-2 DELTA measurement window flush with the probe-adaptor faceplate Tighten the two thumbscrews, making sure that the measurement window stays flush with the probe-adaptor faceplate. - Page 9 103158-01EN [U8998465], Rev. A, April 2012 Locking fixture Figure 5-3 Test-stand locking fixture Align the large tab of the probe adaptor with the large notch of the locking fixture (see Figure 5-4 on page 9). Locking-fixture large notch Probe-adaptor large tab Figure 5-4 Alignment with locking fixture Make sure that the probe-adaptor faceplate is flush with the test chamber floor.
- Page 10 15-pin D-Subminiature connector Figure 5-7 Test-stand I/O panel Plug the USB cable mini USB B connector into the DELTA data port (see Figure 5-8 on page 10). Figure 5-8 Mini USB B connector plugged into the analyzer data port Plug the USB cable USB A connector into a PC USB port.
-
Page 11: Important Information - Please Read Before Use
DANGER fully understood and met. Do not use the DELTA Portable Workstation for any purpose other than its intended use. Instruction Manual The WARNING signal word indicates a potentially hazardous situation. It calls... - Page 12 If a non-approved power supply cord not dedicated to Olympus products is This device complies with the requirements of Directive 2004/108/EC used, Olympus will not be able to ensure the electrical safety of the equipment. concerning electromagnetic compatibility when used in combination with devices bearing the CE marking either on the products or in its instructions.