Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for REXON CT1800R
Summary of Contents for REXON CT1800R
- Page 1 ® 7 IN. (180 MM) MARBLE CUTTER CT1800R INSTRUCTION MANUAL...
- Page 2 CONTENTS P 1 - The original instruction manual is in English.
- Page 3 CARTON CONTENTS UNPACKING 1. Carefully remove the marble cutter from the carton. 2. Separate and layout all of the parts. Carefully check it according to the diagram below. WARNING! If any part is missing or damaged, please do not plug in or use the marble cutter until replacements have been obtained.
-
Page 4: General Safety Rules
General Safety Rules 9. USE PROTECTIVE EQUIPMENT. Use safety glasses. Use face or dust mask if WARNING! When using electric tools cutting operations create dust. basic safety precautions should always 10. CONNECT DUST EXTRACTION be followed to reduce the risk of fire, EQUIPMENT. - Page 5 19. STAY ALERT. Watch what you are 26. USE CORRECTLY SHARPENED SAW BLADES. Observe the maximum doing, use common sense and do not operate the tool when you are tired. speed marked on the saw blade. 20. CHECK DAMAGED PARTS. Before Ensure that the machine is always fixed further use of the tool, it should be to a bench, whenever possible.
-
Page 6: Environmental Protection
14. To avoid injury, if the power cable is Contact your local government for damaged, do not change by yourself. information regarding the collection systems Please contact a qualified engineering available. If electrical appliances are or local manufacturer to deal with. disposed of in landfills or dumps, hazardous 15. -
Page 7: Specification
ASSEMBLING WATER CONNECTOR Specification (FIG. 6) 1. Connect the water hose (1) to the hose Motor ..........1650 W, adaptor (2) by a hose connector (3). 220 V~ 50/60 Hz Blade Size ........Ø180 mm; 2. Install the water hose (1) to the water Ø22.22/Ø25.4 mm Bore valve assembly (4). -
Page 8: Setting The Tool
Setting the Tool Operating the Tool ADJUSTING DEPTH WARNING! CONTROL BRACKET (FIG. 11) Never connect the plug to the power ● source outlet until all installations and WARNING! To avoid injury from an adjustments are completed and you accidental start, ALWAYS make sure have read and understood the safety the switch is in the “OFF”... -
Page 9: Changing Blades
WET CUT Changing Blades WARNING! To avoid electric shock, ALWAYS use WARNING! ● waterproof covers while doing wet cut. Be sure to use Ø 180 mm blade. Other ● Do not touch any electrial device sizes of blades are not recommended. ●... -
Page 10: Replacing Carbon Brushes
REMOVING THE BLADE (FIG. 11, 18, 19) REPLACING CARBON BRUSHES (FIG. 20) WARNING! Replace the blade if cracks NOTE: Replace both carbon brushes or damge on the blade have been found. when either has less than 6 mm length of carbon remaining, or if the spring or wire is 1. - Page 11 Fig. 3 Fig. 4 Fig. 1 Fig. 5 Fig. 2 Fig. 6...
- Page 12 Fig. 7 Fig. 11 Fig. 8 Fig. 12 Fig. 9 Fig. 13 Fig. 10 Fig. 14...
- Page 13 Fig. 15 Fig. 19 Fig. 16 Fig. 20 Fig. 17 Fig. 18...
- Page 14 CT1800R PARTS LIST ORDER ONLY BY MODEL NUMBER AND PART NUMBER I.D. Description Size Q’ty I.D. Description Size Q’ty 0FA1 CLAMP-CORD 38BV WATERPROOF COVER 0HBN COMPRESSION SPRING 38BW FLOW GUIDE 0HX9 NEEDLE BEARING 38BX GEAR BOX 0J4K FLAT WASHER φ10*19-1.8...
- Page 15 Schematic MODEL: CT1800R...
- Page 16 ®...
Need help?
Do you have a question about the CT1800R and is the answer not in the manual?
Questions and answers