Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for REXON MC1850R
Summary of Contents for REXON MC1850R
- Page 1 ® 7-1/4” (185 mm) METAL CUTTER MC1850R INSTRUCTION MANUAL...
- Page 2 CONTENTS P 1 - 8 The original instruction manual is in English.
- Page 3 CARTON CONTENTS UNPACKING 1. Carefully remove the metal cutter from the carton. 2. Separate and layout all of the parts. Carefully check it according to the diagram below. WARNING! If any part is missing or damaged, do not attempt to assemble the planer, plug in the power cord, or turn the switch ON until the missing or damaged part is obtained and is installed correctly.
-
Page 4: General Safety Rules
General Safety Rules for the connection of dust extraction and collecting equipment, ensure these are WARNING! When using electric tools connected and properly used. basic safety precautions should always 11. DO NOT ABUSE THE CABLE. Never be followed to reduce the risk of fire, pull the cable to disconnect it from the electric shock and personal injury. - Page 5 conditions that may affect its operation. 2. Before operation, check the blade A guard or other part that is damaged carefully for cracks or damage. should be properly repaired or replaced Replace the cracked or damaged by an authorised service centre unless blade immediately to avoid the possible otherwise indicated in this instruction hazard.
- Page 6 14. To prevent serious injury, do not use the Special Safety Rules For Kickback tool to cut wood, diamond, magnesium 1. Causes and Operator Prevention of Kickback: or magnalium workpiece. ● Kickback is a sudden reaction to a 15. Wear safety goggles and hearing protection during operation.
-
Page 7: Environmental Protection
● When restarting a tool in the SYMBOLS workpiece, center the saw blade in V ……..volts A …..…...amperes the kerf and check that saw teeth Hz ….….hertz W ......watts are not engaged into the material. If min …..minutes ~ ..alternating current saw blade is binding, it may walk up h …..hours I ………....ON... -
Page 8: Installation
Installation Assembly KNOW YOUR METAL CUTTER (FIG. 1) WARNING! For your own safety, never Side cover connect the plug to power source outlet Rip fence until all assembly steps are completed Lower blade guard and you have read and understood the Base safety and operational instructions. -
Page 9: Setting The Tool
7. Replace the outer flange (6), washer (5) HEX WRENCH STORAGE (FIG. 6) and arbor bolt (4). 1. Place the hex wrench (1) into the hole (2) on the left side of the tool for storage WARNING! Make sure the collars are when not in use. -
Page 10: Operating The Tool
USING AN EXTENSION LEAD USING THE AUXILIARY HANDLE The use of any extension lead will cause (FIG. 10) some loss of power. To keep this to a The auxiliary handle (1) is pre-assembled minimum and to prevent overheating and at the factory. It alows the user holding motor burn-out, ask advice from a qualified firmly while doing the cutting operation with electrician to determine the minimum wire... -
Page 11: Maintenance
Maintenance WARNING! To avoid injury from an accidental start, make sure the switch is in the OFF position and the plug is not connected to the power source outlet. Use clean cloth to remove dirt, dust, oil, grease, etc. Do not use gasoline, turpentine, lacquer or paint thinner, dry cleaning fluids or similar products. - Page 12 Fig. 4 Fig. 1 Fig. 5 Fig. 2 Fig. 6 Fig. 3 Fig. 7...
- Page 13 Fig. 8 Fig. 12 bottom line Fig. 9 Fig. 13 Fig. 10 Fig. 11...
- Page 14 MC1850R PARTS LIST ORDER ONLY BY MODEL NUMBER AND PART NUMBER I.D. Description Size Q'ty I.D. Description Size Q'ty 083Z CORD CLAMP 3BGT HANDLE (LEFT) 0CFZ WRENCH SET 3BHT HANDLE (RIGHT) 0D9A ANCHOR BLOCK 3BJS SIDE COVER 0J4M FLAT WASHER φ12*21-1...
- Page 15 Schematic MODEL: MC1850R...
- Page 16 ®...
Need help?
Do you have a question about the MC1850R and is the answer not in the manual?
Questions and answers