Advertisement
Quick Links
W2119 & W2120 SERIES IMPACTS
Impact Wrench:
Handle:
T
Inside Trigger
Outside Trigger
Tool Size:
2119
2120
NORTH AMERICA
CooperTools
P.O. Box 1410
Lexington, SC 29071
W
X
X
-
XXXX
-
Operation & Service Manual
823036
X
Output Drive:
12
1 1/2"
S
Spline Drive (No. 5 Spline)
EUROPE
Cooper Power Tools GmbH & Co.
Postfach 30
D-73461 Westhausen
2/01
1
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Cleco W2119 series
Summary of Contents for Cleco W2119 series
- Page 1 Operation & Service Manual 823036 2/01 W2119 & W2120 SERIES IMPACTS XXXX Impact Wrench: Handle: Output Drive: Inside Trigger 1 1/2" Outside Trigger Spline Drive (No. 5 Spline) Tool Size: 2119 2120 NORTH AMERICA EUROPE CooperTools Cooper Power Tools GmbH & Co. P.O.
- Page 2 Repetitive work motions and/or vibration may cause injury to hands and arms. Cleco impact wrenches are designed to operate on 90 psig (6.2 Use minimum hand grip force consistent bar) maximum air pressure. If the tool is properly sized and with proper control and safe operation.
- Page 3 SafetyRecommendations presently unknown to what extent exposure to vibrations or Work gloves with vibration reducing liners and wrist supports repetitive motions may contribute to the disorders. Hereditary are available from some manufacturers of industrial work factors, vasculatory or circulatory problems,exposure to cold gloves.
-
Page 4: General Information
front of the motor unit. The anvil housing may need to be GENERAL INFORMATION rotated to clear the anvil and hammer lugs. AIR SUPPLY Thetool isdesigned to operate on 90 psig (6.2 bar) airpressure The impact wrench is now separated into four (4) basic (measured at the tool air inlet with the tool running) using a assemblies. - Page 5 No. 867974, from the tapered end. Inspect the "O"-ring, No. should not be removed from the housing unless replace- 863009, and replace if necessary. Clean the threads on the ment is necessary. If cylinder replacement is necessary, a 4- air inlet bushing, No 864972, and apply "LOCKTITE" No. 271 5/32"...
-
Page 6: General- All Models
onto the front of the cam shaft and hammer assembly. GENERAL- ALL MODELS Rotate the spring clip to accept the anvil pin and then install Coat the hammer and rotor splines with 30W oil and insert the anvil on top of the assembly (be sure the slot in the anvil the impact mechanism into the front of the rotor Lubricate the lines up with the anvil pin) and drive the anvil down until the anvil housing seal and bushing with 30W oil and install on the... - Page 8 PARTS LIST — IMPACT MECHANISM PART NO. NAME OF PART QTY. PART NO. NAME OF PART QTY. Support Handle 867984 Hammer Spring 842290 861602 Anvil Housing Bushing (incl. 867976, 867983, 867987, 867987 Thrust Bearing 867988) 867988 Thrust Race 861605 Anvil Housing (incl. 861602, 867993) 867990 Support Handle Bracket 867949...
- Page 9 PARTS LIST — MOTOR UNIT PART NO. QTY. PART NO. NAME OF PART QTY. NAME OF PART 863096 O-ring 3-1/4" X 3-1/2" 867996 Rotor Shaft Seal 863637 Wear Plate Pin 869001 Motor Clamp Seal Wear Plate 865004 869004 Muffler Plate 867971 Cylinder (W-2120) 869596...
- Page 10 PARTS LIST — HANDLES PART NO. NAME OF PART QTY. PART NO. NAME OF PART QTY. 203282 Washer 867801 30W Oil Fill Plug 832125 Trigger Pin 867974 throttle Valve Air Inlet Screen 867977 Throttle Valve Seal 843656 844303 O-ring 3/16" X 5/16" 867982 Throttle Valve Pin 847981*...
- Page 11 NOTES...
- Page 12 CooperTools 670 Industrial Drive Lexington, SC 29072 Phone: (803) 359-1200 Fax: (803) 359-2013 www.cooperindustries.com...
Need help?
Do you have a question about the W2119 series and is the answer not in the manual?
Questions and answers