Sea&Sea 31133 Instruction Manual

Nikon AF-S VR Micro-Nikkor ED 105mm F2.8G(IF) Focus Gear
31133
0809-Z-01A
Thank you for purchasing SEA&SEA products.
Please read this instruction manual carefully prior to using this product. Only with a thorough understanding of this manual's content will you
be able to use the product correctly. After reading the manual, please be sure to keep it in a place where you can easily come back to it at any time.
Precautions
Failure to heed the precautions listed below could result in serious consequences. To prevent injury damage to yourself and/or others,
please observe the precautions as they contain highly important information related to personal and product safety.
CAUTION
Situations that could result in property damage or personal injury.
CAUTION
Carefully observe the instruction manual for the compatible lens
for this product before use.
This product includes an O-ring (divided into pieces) for
interlocking the lens and the gear. In some cases, the interlocking
may be too tight or loose when attaching focus gear A, due to
deviation in the lens diameter.
①When too tight
Remove the O-ring pieces from inside the gear and cut them
shorter with scissors. Re-insert these pieces into the grooves
inside the gear, providing ample space between the pieces.
Adjust the length of the O-ring pieces for appropriate tightness.
Do not force the lens into the gear when the interlocking is

too tight, because this may result in damage to the lens.
②When too loose
Replace the O-ring with the thicker O-ring that was also supplied
with this product. If it becomes too tight with the thicker
O-ring, adjust the interlocking tightness as explained above ①.
Focus Gear
This product is designed for manual-focus operation utilizing the
focus/zoom dial on SEA&SEA digital SLR camera housings.
How to Attach to the Lens
1
Attach focus gear A (①) to the lens first, then attach
focus gear B (②) in parallel alignment with the lens
as shown in Fig.1.
②
①
Focus gear B
Lens foreside
Focus gear A
Push down on focus gear A until it
comes to a stop.
Set focus gear A to a position
that is approx. 12mm from the
lens tip as shown in Fig.2.
Specifications
Construction Corrosion-resistant aluminum alloy
)
Dimensions(DIA×D
Approx. 158g / 5.5oz
Weight
Accessories Focus gear A・Focus gear B・Screws (3 pcs + 1 spare)・Screw driver・O-ring・
Gear sheet (stick-on)
Instruction Manual
If it is still too loose, use the gear sheet which is included in
the package. Cut the sheet into 3 to 6 pieces with scissors,
and apply them between the grooves inside the gear.
The thicker O-ring may not be compatible with some lenses

due to size restrictions. In this case, adjust the tightness by
following the above procedure ① and using the gear sheet
included in the package.
Always make sure that the gear and the lens work properly after
adjustment.
SEA&SEA SUNPAK Co., Ltd. will not be responsible for the
replacement or compensation for cameras, lenses or those
accessories damaged due to your invalid operation.
Use supplied screws to securely mount gears in order to prevent
damage, dropping or loss.
SEA&SEA SUNPAK Co., Ltd. assumes no liability for compensation
of loss of captured images or expenses caused by loss of images,
even if you are unable to shoot due to a product defect or malfunction.
This product should be used in combination with the DX Macro
Port Base (30105) + DX Macro Port 50 (30106).
2
Align the cutout parts
on focus gears A &
B, and firmly attach
both gears with 3
screws (included in
the package) using
the supplied screw
driver as shown in
Fig.3.
Fig.1 Screw
3
Mount the lens, with the focus gear attached, to the
camera .
Always make sure that the lens with the focus gear
works properly after attaching the lens to the camera.
CAUTION
Please make sure the O-ring pieces inside the focus gear

do not come out of the grooves when detaching the focus
gear from the lens.
Fig.2
Approx. φ95×91mm / 3.8×3.6inch
* The specifications and appearance are subject to change without notice.
Mounting
1
Attach the DX Macro Port Base (30105) + DX Macro Port 50 (30106)
to the housing first.
2
Set the switches on the lens to the appropriate selections for your
shooting condition.
3
Rotate the focus gear on the lens to align the yellow indicators to
the gearwheel inside the housing.
4
The gearwheel can only be passed in between the yellow
indicators. Carefully slide the camera forward into the housing,
while avoiding contact with the focus gear. (Fig.4)
Always make sure the focus gear and the gearwheel are properly
engaged after mounting the camera to the housing.
Removing
1
Rotate the focus/zoom dial on the housing to align the yellow
indicators to the gearwheel. (Fig.4)
2
Carefully slide the camera toward you while avoiding contact with
the focus gear.
CAUTION
Do not mount/remove the camera without aligning the yellow indicators and the

gearwheel, because this may result in damage to the camera, housing, lens
or focus gear.
Refer to the each port instruction manual for installation.

CAUTION
Those four housing have different mounting procedure. Attach the DX Macro
Port Base (30105) + DX Macro Port 50 (30106) to the housing at the last.
Mounting
1
Set the switches on the lens to the appropriate selections for your
shooting condition.
2
Rotate the focus gear on the lens to align the yellow indicators to
the gearwheel inside the housing.
3
Screw The gearwheel can only be passed in between the yellow
Cutout part indicators. Carefully slide the camera forward into the housing,
while avoiding contact with the focus gear. (Fig.5.①)
4
Attach the DX Macro Port Base (30105) + DX Macro Port 50 (30106)
to the housing. (Fig.5.②)
Always make sure the focus gear and the gearwheel are properly
engaged after mounting the camera to the housing.
Fig.3
Removing
1
Remove the Port from the housing first.
2 Rotate the focus/zoom dial on the housing to align the yellow
indicators to the gearwheel.
3
Carefully slide the camera toward you while avoiding contact with
the focus gear.
CAUTION
Do not mount/remove the camera without aligning the yello s and the

gearwheel, because this may result in damage to the camera, housing, lens
or focus gear.
Refer to the each port instruction manual for installation.

http://www.seaandsea.jp
Mounting / Removing the Camera to / from the Housing
For DX-D200・DX-D50・DX-D70・DX-S5Pro Housings
SEA&SEA SUNPAK Co., Ltd.
3-2-20, Saiwai-cho, Kawaguchi-shi, Saitama, Japan 332-0016 TEL. +81-48-256-2251
World Customer Service Center TEL. +81-48-255-8512
Housing inside (front case)
Gearwheel
Yellow indicator
Focus gear
(on the lens)
Port
(DX Macro Port Base (30105) +
DX Macro Port 50 (30106))
Fig.4
Focus/zoom dial
Housing inside (front case)
Gearwheel
Port
(DX Macro Port Base (30105) +
DX Macro Port 50 (30106))
Yellow indicator
Focus gear
(on the lens)
②
①
Housing
(DX-D200・DX-D50・
DX-D70・DX-S5Pro)
Camera Fig.5
(Current as of May.2012)