Table of Contents
Advertisement
Quick Links
VENUE AO16 Analog Output
9321-61199-00 REV A 03/09
For VENUE Mix Rack and VENUE SC48
Card
Digidesign
2001 Junipero Serra Boulevard
Daly City, CA 94014-3886 USA
tel: 650·731·6300
fax: 650·731·6399
Technical Support (USA)
tel: 650·731·6100
fax: 650·731·6375
Product Information (USA)
tel: 650·731·6102
tel: 800·333·2137
International Offices
Visit the Digidesign Website
for contact information
Website
www.digidesign.com
™
Advertisement
Table of Contents
Related Manuals for DigiDesign VENUE AO16
Summary of Contents for DigiDesign VENUE AO16
- Page 1 VENUE AO16 Analog Output Card ™ For VENUE Mix Rack and VENUE SC48 Digidesign 2001 Junipero Serra Boulevard Daly City, CA 94014-3886 USA tel: 650·731·6300 fax: 650·731·6399 Technical Support (USA) tel: 650·731·6100 fax: 650·731·6375 Product Information (USA) tel: 650·731·6102 tel: 800·333·2137...
- Page 2 NOTE: This equipment has been tested and found to comply with the limits for a This guide is copyrighted ©2009 by Digidesign, a division of Avid Technology, Inc. Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are (hereafter “Digidesign”), with all rights reserved.
-
Page 3: Table Of Contents
Contents Chapter 1. Overview ................1 AO16 Card Components . - Page 4 AO16 Analog Output Card...
-
Page 5: Chapter 1. Overview
– or – The AO16 Card includes the following items: • An SC48 console with an available output card slot • AO16 Card For complete system requirements, visit the Digidesign • Mounting screws website (www.digidesign.com). • Digidesign Registration Information Card •... -
Page 6: Conventions Used In This Guide
Conventions Used in This Guide All Digidesign guides use the following conventions to indi- cate menu choices and key commands in D-Show and Pro Tools: Convention Action File > Save Session In Pro Tools, choose Save Session from the File menu. -
Page 7: Chapter 2. Installing The Ao16 Card
Chapter 2: Installing the AO16 Card This chapter provides information on installing an AO16 card in a Mix Rack or an SC48 console. Mounting screws (remove all) For instructions on installing a card in a Mix Rack, see “Install- ing an AO16 Card in Mix Rack” on page 3. For instructions on installing a card in an SC48 console, see “Installing an AO16 Card in SC48”... - Page 8 On the back panel of Mix Rack, locate output slot E and re- Find the Hub48 Board ribbon cable that corresponds to the move the card slot cover. output slot in which you have installed the card. The Hub48 board’s five ribbon cables connect to the input and output cards Do not remove or re-seat the ribbon cable connections on the Hub48 Board while the board is installed in the Mix...
-
Page 9: Installing An Ao16 Card In Sc48
Completing and Confirming Installation Installing an AO16 Card in SC48 To complete and confirm installation: Your SC48 has two available output card slots, lots D and E. AO16 Cards can be installed in either or both slots. These in- Reattach Mix Rack’s front panel. structions assume you already have an AO16 Card installed in Reconnect the power and any audio cables to Mix Rack. - Page 10 Remove the card from its packing material. Hold the card by Completing and Confirming Installation its edges. To complete and confirm installation: Connect the ribbon cable to the card socket. Make sure the Reconnect the power cable and any other cables to the pins on the socket are correctly aligned with the ribbon cable SC48.
-
Page 11: Chapter 3. Specifications
Chapter 3: Specifications Audio Specifications AO16 Analog Line Outputs Parameter Specifications Limit Units Condition/Comment Type Balanced, XLR3-Male Impedance Each leg to ground Maximum Output Level D/A Converter Latency 0.58 Fs=48kHz All measurements at Fs=48 kHz with 150 Ohm source impedance and 600 Ohm load impedance, unless otherwise specified. 0 dBU = 0.775Vrms. - Page 12 AO16 Expansion Card Guide...
Need help?
Do you have a question about the VENUE AO16 and is the answer not in the manual?
Questions and answers