Table of Contents
Advertisement
Read the instructions carefully and follow the rules for safe
operation.
Failure to do so could result in serious injury.
ECHO, INCORPORATED
400 Oakwood Road, Lake Zurich, Illinois 60047-1564
Phone : 847-540-8400
OPERATORS MANUAL
THIS PRODUCT COMPLIES WITH CAN ICES-2/NMB-2
WARNING
1
CHAIN SAW
CS-4510
X7503350601
CS-4510
1/18
Advertisement
Table of Contents
Related Manuals for Echo CS-4510
Summary of Contents for Echo CS-4510
-
Page 1: Operators Manual
OPERATORS MANUAL CHAIN SAW CS-4510 THIS PRODUCT COMPLIES WITH CAN ICES-2/NMB-2 WARNING Read the instructions carefully and follow the rules for safe operation. Failure to do so could result in serious injury. ECHO, INCORPORATED 400 Oakwood Road, Lake Zurich, Illinois 60047-1564... - Page 2 WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Copyright © 2017 All Rights Reserved. CS-4510...
-
Page 3: Rules For Safe Operation
The Kick Guard device is not installed on the guide bar when you purchase your 3. Make sure that the area in which you ECHO chain saw. are cutting is free from obstructions. ® The Kick Guard can be used in a majority... - Page 4 19. Spark arrestor mufflers approved to SAE 6. Do not start cutting until you have a clear work Standard J335 are standard on ECHO chain area, secure footing, and a planned retreat saws to reduce the possibility of forest fires.
-
Page 5: Table Of Contents
The enclosed message provides information CAUTION necessary for the protection of the unit. The safety alert symbol accompanied by the word “CAUTION” calls attention to an act or condition which may lead to minor or moderate personal injury if not avoided. CS-4510... -
Page 6: X505
PARTS” section will help you locate them. Make sure the decal is legible and that you understand and follow the instructions on it. If a decal cannot be read, a new one can be ordered from your ECHO dealer. CS-4510... -
Page 7: Packing List
The ECHO product you purchased has been After opening the carton, check for damage. factory pre-assembled for your convenience. Immediately notify your retailer or ECHO dealer of Due to packaging restrictions, guide bar and saw damaged or missing parts. chain installation and other assembly may be Use the packing list to check for missing parts. -
Page 8: Nomenclature Of Parts
NOMENCLATURE OF PARTS OPERATORS X505-010090 Part Number X505-010090 * If a decal cannot be read, a new one can be ordered from your ECHO dealer. CS-4510... - Page 9 11. Guide bar - The part that supports and guides the saw chain. 12. Saw chain - Chain, serving as a cutting tool. 13. Bar tip guard - Anti-kickback device attached on the bar nose. CS-4510...
-
Page 10: Operator Safety
If this guideline is not followed, hearing loss can numbness in the fingers. occur. The following precautions are strongly ECHO recommends wearing hearing protection recommended because the minimum exposure at all times. which might trigger the ailment is unknown. WEAR PROPER CLOTHING •... -
Page 11: Correct Use Of Chain Brake
ECHO chain brakes have been designed and Reduced radius belongs on top tested to comply with international safety standards as follows. -
Page 12: Preparation For Use
Never start or operate saw if brake band is not in place on clutch drum. Always check chain brake operation after replacing cover. Do not use saw if chain brake does not function properly. CS-4510... - Page 13 5. Pull the chain around the bar by hand. Loosen the adjustment if you feel tight spots. 6. When chain is properly tensioned, tighten clutch cover nuts securely - 20 to 23 N·m (175 to 200 in. lb.). 7. Keep chain properly tensioned at all times. CS-4510...
-
Page 14: Fuel And Lubricant
ECHO requirements are NOT approved for 93 octane, ethanol-free fuel premixed with ECHO use in ECHO 2-stroke gasoline engines. Red Armor™ engine oil at 50:1 ratio. Use of ECHO Use of diesel or alternative fuels may cause Red Armor™ Fuel (Power Fuel™) is recommended... - Page 15 Fueling - When fuel tank cap or oil tank cap is difficult to re- move, remove spark plug lead, pull starter handle slowly, and use starter handle to assist in removing cap. CS-4510...
-
Page 16: Emission Data
• Do not use used or reclaimed oil to avoid various oiler problems. • Use ECHO bar and chain oil. • Use bar and chain oil of the following grades: SAE No. 30 ..in summer SAE No. 10 ..in winter or when cutting... -
Page 17: Operation
Purge pump release fast idle throttle latch, otherwise Throttle trigger severe brake damage may occur. • Never use fast idle throttle latch for cutting. • Use the fast idle throttle latch only in starting. Starter handle CS-4510... - Page 18 • Securely hold the chain saw as shown and pull starter handle. • Choke may be used if necessary, but after first firing sound, squeeze and release throttle trigger Starter handle to release fast idle throttle latch otherwise severe brake damage may occur. CS-4510...
-
Page 19: Checking Chain Tension
NOTICE If engine does not stop, pull choke control knob out fully to stop engine. Throttle trigger Return the unit to your authorized ECHO dealer to check and repair moentary stop switch before starting the engine again. CHECKING CHAIN TENSION •... -
Page 20: Cutting Instruction
CUTTING INSTRUCTION GENERAL CAUTION • Read the ECHO “CHAIN SAW SAFETY MANUAL” included with your chain saw for additional cutting and safety instructions. • Wear suitable hearing protection such as earmuffs or earplugs to protect against objectionable or uncomfortable loud noises. - Page 21 Then remove the saw for the second cut. Insert the saw in the first cut, very carefully so as not to cause kickback. The final cut is made by drawing the saw forward in the cut to reach the hinge. CS-4510...
- Page 22 • The chain saw industry and government agencies have attempted to prescribe various safety devices, but the best protection is to avoid kickback. • Comply with the safety precautions as listed in this Manual and Safety Manual. CS-4510...
-
Page 23: Chain Brake Operation
When the brake lever trips, the chain should stop. Immediately release the throttle trigger. WARNING If the chain does not stop immediately, return the saw to your authorized ECHO dealer for Chain brake unlock repair. When the lever is fully pulled toward the operator, brake is unlocked. -
Page 24: Automatic Chain Brake
4. The impact should lock the chain brake. IMPORTANT When checking the operation of the automatic chain brake, use a soft surface substance like wood to provide the impact so the chain is not damaged. Rear handle should be gripped lightly with the right hand. CS-4510... -
Page 25: Chain And Guide Bar Combination
CHAIN AND GUIDE BAR COMBINATION The following combinations are recommended for model CS-4510. Guide bar Saw chain Length mm (in.) ECHO Part No. Pitch mm (in.) ECHO Part No. Links 406 (16) 16B0AD3366 20BPX66CQ / 95TXL66CQ 457 (18) 18B0AD3372 8.26 (0.325) -
Page 26: Maintenance And Care
MAINTENANCE AND CARE SKILL LEVELS Your ECHO chain saw is designed to provide many hours of trouble free service. Regular scheduled Level 1 = Easy to do. Most required tools come maintenance will help your chain saw achieve that with unit. -
Page 27: Carburetor Adjustment
To maintain proper engine operation and above 330 m / 1,100 ft ASL the carburetor may need to be CAUTION adjusted by an authorized ECHO service dealer. When starting, idling adjustment speed IMPORTANT should be adjusted not to rotate the saw If the engine is adjusted for operation above chain. -
Page 28: Air Filter
• The standard spark gap is 0.65 mm (0.026 in.). • Correct the spark gap if it is wider or narrower than the standard gap. • Fastening torque: 15 to 17 N·m (130 to 145 in. lb.). 0.65 mm (0.026 in.) CS-4510... -
Page 29: Fuel Filter
• A damaged sprocket will cause premature damage or wear of saw chain. - When the sprocket has worn out 0.5 mm (0.02 in.) or more, replace it. • Check sprocket when you install new chain. Replace it if worn. CS-4510... -
Page 30: Automatic Oiler
Adjusting screw adjusting screw counterclockwise. When the screw touches stopper and stops, this position indicates maximum discharge volume. (13 mL/min at 7,000 r/min) - Do not turn the adjusting screw beyond the maximum or minimum limit of volume adjustment. CS-4510... -
Page 31: Setting The Saw Chain
• For setting saw chain, round file 4.8 mm (3/16 in.) diameter and flat file are used. • To keep correct position and correct angle, use Keep this angle ® the file holder (Sure Sharp 30° Push file as shown 10° Hold the file tipped 10° upward CS-4510... - Page 32 - If the saw chain becomes soiled with resin, for instance, clean it with kerosene and soak in it oil. NOTICE Parallel These angles are referred to as Oregon 20BPX or 95TXL. To sharpen other follow chain manufacturer’s Depth gauge instruction. CS-4510...
-
Page 33: Troubleshooting
• Fuel filter clogged • Clean or replace cranks carburetor carburetor • Fuel line clogged • Clean • Carburetor • Ask your ECHO dealer Fuel at No fuel at • Carburetor • Ask your ECHO dealer cylinder cylinder Muffler wet with •... -
Page 34: Storage After Use
Recoil starter Power transmission Automatic centrifugal clutch Fuel Mixture ratio 50:1 ratio with ECHO Power Blend X™ or ECHO Red Armor® ISO-L-EGD (ISO/CD 13738) and JASO M345-FD two-stroke, air-cooled engine oil. Gasoline Use 89 octane unleaded. Do not use fuel containing methyl alcohol, more than 10 % ethyl alcohol or 15 % MTBE. -
Page 35: Warranty Registration Sheet
Please go to http://www.echo-usa.com/Warranty/Register-Your-ECHO to register your new product on-line. It’s FAST and EASY! NOTE: your information will never be sold or misused by ECHO, Inc. Registering your purchase enables us to contact you in the unlikely event of a service update or product recall, and verifies your ownership for warranty consideration. - Page 36 C71315001001 - C71315999999 CS-4510...