Download
Share
Print this page
Casio fx 9750 G PLUS User Manual
  1. Manuals
  2. Brands
  3. Casio Manuals
  4. Calculator
  5. fx-9750G PLUS
  6. User manual

Casio fx 9750 G PLUS User Manual

Graphing calculator
Hide thumbs Also See for fx 9750 G PLUS:

Advertisement

Quick Links

Download this manual See also: Programming Manual, User Manual
C asio fx 9750 G PLUS
User's guide
For estimation of isolation and ventilation parts
1. Pipe bend partition to 12 or 24
2. T-connector straight on regular pipe partition to 12 or 24
3. T-connector warped on regular pipe
4. T-connector not centric on regular pipe
5. Cone, long parted to several cones
6. Cone with triangles
7. Cone with radius
8. Cone end
9. Zeppelin
10. Insertion
11. Change angular to round
12. Measure of angle in degrees 200-200 method
13. Medium part to 45 degrees bend on ventilation (spiro)
14. EURO > currency

Advertisement

loading

Related Manuals for Casio fx 9750 G PLUS

Summary of Contents for Casio fx 9750 G PLUS

  • Page 1 C asio fx 9750 G PLUS User’s guide For estimation of isolation and ventilation parts 1. Pipe bend partition to 12 or 24 2. T-connector straight on regular pipe partition to 12 or 24 3. T-connector warped on regular pipe 4.
  • Page 2 Casio fx-9750 G PLUS ON and OFF CASIO: AC/ON Press (AC) AC/ON Press (Shift and AC) SHIFT Open program: Drive with arrowbutton black cursor to (PRGM) Choose from MAIN MENU…………. Press – BLUE EXE…………………Press LANGUAGE Press Start program: Press – Choose language Press...
  • Page 3 Estimation of BEND from the edge Note! Sections in 4 parts are: 3 whole and 2 halfsections Overlappin Half section You get the next measure: Full section Partition to 12 or 24 Figure to pattern Center radius The distance of the holes from the edge Middle line Pattern length with overlapping Keep distance...
  • Page 4 T-connector Diameter Diameterr T-connecto Combined: Regular pipe Straight T-connector Warped T-connector Side T-connector Middle line difference Angle to regular pipe You get the next measure: Partition to 12 or 24 Figure to patter The figure is measured from below Partition direction...
  • Page 5 Page 5 Long cone: several cones in a row Large diameter Center difference Partition Small diameter Whole length to cone Thereafter, the program goes to program: “Cone with triangles”. Measure to cone come after each other continuously, starting from small cone and ending with the last large cone.
  • Page 6 Cone with triangles Small diameter Center difference Length to cone Large diameter You can choose partition yourself Small diameter parted to 6 Large diameter parted to 6 Here is only half part of the cone, so you have to draw a similar part to get the whole cone.
  • Page 7 Cone with radius Small diameter Large diameter Length to crossing Large radius Small radius Partition is 12 or you can choose quantity of partitions yourself.
  • Page 8 Conical end or finish. Casio asks about isolation diameter or pipe diameter. You get large radius or small radius. Draw a big circle and a small circle, take away ¼ part from the drawing and overlap. Large diameter Small diameter Overlapping ¼...
  • Page 9 Diameter Attention: Even numbers Please remember !!! Quantity of sections should be even numbers Figures on the sides Straight Partition to pattern...
  • Page 10 Insertion Measre to insertone Length to straight line Measure to insertione Diameter Length to straight line Shortened length Turning-point Shorter Shorter Shortert Shortert...
  • Page 11 Change from square to round Partition to round, can be decided by yourself. Diameter to round Please remember! Even numbers Length Centre +/- difference change Side A If you draw the other half part the same, you get the complete change Side B Diameter Centre +/- difference...
  • Page 12 The angle is measured into degrees The angle is measured with the 200 and 200 method You get Answer directly in degrees! 200 mm This distance to be measured 200 mm...
  • Page 13 Ventilation channel spiro (difference = pass length) Diameter Difference measures...