Advertisement
Quick Links
What This Kit Contains
Tools That You Need
Logix Expansion Board for DriveLogix
ATTENTION: To avoid an electric shock hazard, verify that the
!
voltage on the bus capacitors has discharged before performing
any work on the drive. Measure the DC bus voltage at the +DC &
–DC terminals of the Power Terminal Block. The voltage must
be zero.
ATTENTION: HOT surfaces can cause severe burns. Do not
!
touch the heatsink surface during operation of the drive. After
disconnecting power allow time for cooling.
ATTENTION: This drive contains ESD (Electrostatic
!
Discharge) sensitive parts and assemblies. Static control
precautions are required when installing, testing, servicing or
repairing this assembly. Component damage may result if ESD
control procedures are not followed. If you are not familiar with
static control procedures, reference A-B publication 8000-4.5.2,
"Guarding Against Electrostatic Damage" or any other
applicable ESD protection handbook.
Verify that your kit contains the items listed in the following table. If your
kit does not contain the correct items, contact your Allen-Bradley sales
representative.
Quantity:
Description
1
DriveLogix5730 Expansion Board
4
Screws
• Phillips
®
screwdriver for M3 screws
• Standard (flat blade) screwdriver
®
Phillips
is a registered trademark of Phillips Screw Company
Installation Instructions
™
5730
Advertisement
Related Manuals for Allen-Bradley DriveLogix 5730
Summary of Contents for Allen-Bradley DriveLogix 5730
- Page 1 Installation Instructions ™ Logix Expansion Board for DriveLogix 5730 ATTENTION: To avoid an electric shock hazard, verify that the voltage on the bus capacitors has discharged before performing any work on the drive. Measure the DC bus voltage at the +DC & –DC terminals of the Power Terminal Block.
-
Page 2: What You Need To Do
Logix Expansion Board for DriveLogix™5730 What You Need to Do To install the DriveLogix5730 Expansion Board: ❐ Step 1: Remove power from the drive ❐ Step 2: Open the main drive door ❐ Step 3: Remove the control cassette from the drive ❐... -
Page 3: Step 1: Removing Power From The Drive
Logix Expansion Board for DriveLogix™5730 Step 1: Removing Power from the Drive ATTENTION: To avoid an electric shock hazard, verify that the voltage on the bus capacitors has discharged before performing any work on the drive. Measure the DC bus voltage at the +DC & –DC terminals of the Power Terminal Block. - Page 4 Logix Expansion Board for DriveLogix™5730 Step 2: Opening Door Over Power Structure and Main Control Board Frames 1-4 Locate the slot in the upper left corner. Slide the locking tab up and swing the cover open. Special hinges allow cover to move away from drive and lay on top of adjacent drive (if present).
- Page 5 Logix Expansion Board for DriveLogix™5730 Step 4: Removing the Outside Covers from the Control Cassette Proper tightening torque for Task Description reassembly is 7-10 lb.-in. Loosen screws on face of front cover and remove the cover Loosen screws on side of rear cover and remove the cover Step 5: Removing the Skip this step if you are installing a new DriveLogix5730 Expansion Board...
- Page 6 Logix Expansion Board for DriveLogix™5730 Step 6: Installing the DriveLogix5730 Expansion Board Task Description Align connector on DriveLogix5730 Expansion Board with connector on Main Control Board Place DriveLogix5730 Expansion Board on the Main Control Board Install and tighten screws (7-10 lb.-in.) Step 7: Installing and Referring to the documentation for the options, install them.
- Page 7 Logix Expansion Board for DriveLogix™5730 Step 9: Documenting Document drive revisions on the “Field Installed Options” tag. Use the blank line if you are installing the DriveLogix5730 Expansion Board in a Revision Changes drive that was manufactured without it. FIELD INSTALLED OPTIONS Firmware Date Date...
- Page 8 Publication 20D-IN013A-EN-P - August 2004 P/N 342550-P01 Copyright © 2004 Rockwell Automation. All rights reserved. Printed in USA.