PRODUCT INTRODUCTION MG3700A Vector Signal Generator Connection to LAN ANRITSU CORPORATION...
Page 2
CONFIDENTIAL Copyright 2005 by ANRITSU CORPORATION The contents of this manual shall not be disclosed in any way or reproduced in any media without the express written permission of Anritsu Corporation.
Connection to LAN MG3700A Vector Signal Generator This document describes how to connect MG3700A Vector Signal Generator and a PC via LAN. An Ethernet connector of MG3700A is used for LAN connection. MG3700A rear panel MG3700A front panel Ethernet connector...
Page 4
[Method 1: Direct connection] 1/4 LAN cable (cross type) 1. Setting of a PC ................P2 2. Setting of a MG3700A ..............P4 3. Connection by Transfer&Setting of IQproducer ......P5 1. Setting of a PC (slightly differs depending on the type of OS) (a) Network setting Open [Network and Dial-up Connections] from [Start] >...
Page 5
IP address] and enter an arbitrary address in the edit box of [IP address]. The IP address entered here must be different from the address of MG3700A that will be specified later. Also, [Subnet mask] and [Use the following DNS server addresses] are set automatically in the course of operations above.
Page 6
Connection to LAN MG3700A Vector Signal Generator [Method 1: Direct connection] 3/4 2. Setting of a MG3700A Press [Utility] on the front panel. Press [F5: Network Setup]. Wait until the screen display (below left) changes to the right one. Change the setting of [DHCP] from ON to OFF.
Page 7
(The following describes the procedures in the state IQproducer that is the standard software of MG3700A is installed.) Open [IQproducer for MG3700A] from [Start] > [Programs] > [Anritsu Corporation]. Open [Transfer & Setting Panel] from [Transfer & Setting] of IQproducer.
Page 8
(straight type) (straight type) 1. Setting of a PC ................P6 2. Setting of a MG3700A ..............P8 3. Connection by Transfer&Setting of IQproducer ......P9 1. Setting of a PC (slightly differs depending on the type of OS) (a) Network setting Open [Network and Dial-up connections] from [Start] >...
Connection to LAN MG3700A Vector Signal Generator [Method 2: Network connection] 2/4 1. Setting of a PC (slightly differs depending on the type of OS)…continued Activate radio buttons of [Obtain an IP address automatically] and [Obtain INS server address automatically] and click [OK].
Check [IP Address] above. Display/Non-display of the IP address can be switched by pressing [F3: IP Display]. Please try any of the following actions if you cannot obtain the [IP Address]. Confirm that [DHCP] is [ON]. Restart MG3700A in the state a LAN cable is connected. Press [F1: Renew].
(The following describes the procedures in the state IQproducer that is the standard software of MG3700A is installed.) Open [IQproducer for MG3700A] from [Start] >[Programs] > [Anritsu Corporation]. Open [Transfer & Setting Panel] from [Transfer & Setting] of IQproducer. When a [Connection to MG3700A]...
Page 12
ANRITSU COMPANY LTD. 1155 East Collins Blvd., Richardson, TX 75081, U.S.A. Via Elio Vittorini, 129, 00144 Roma EUR, Italy Beijing Representative Office Toll Free: 1-800-ANRITSU (267-4878) Phone: +39-06-509-9711 Room 1515, Beijing Fortune Building, No. 5 North Phone: +1- 972-644-1777 Fax: +39-06-502-2425 Road, the East 3rd Ring Road, Chao-Yang District •...
Need help?
Do you have a question about the MG3700A and is the answer not in the manual?
Questions and answers