Cisco SG300 Setup Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Switch
  5. SG300 series
  6. Setup manual

Cisco SG300 Setup Manual

When used with elan video over ip products
Hide thumbs Also See for SG300:

Advertisement

Table of Contents

Cisco SG300 Setup Guide
When used with ELAN Video Over IP products

Advertisement

Table of Contents
loading

Related Manuals for Cisco SG300

Summary of Contents for Cisco SG300

  • Page 1 Cisco SG300 Setup Guide When used with ELAN Video Over IP products...

  • Page 2: Table Of Contents

    Cisco SG300 SETUP GUIDE Contents Introduction Cisco Feature Requirements Connecting To The Web GUI Interface Activating Layer 3 Mode Jumbo Frames IGMP Snooping 07-09 Turning On/Off POE Apply And Save Settings Changing Your Computer IP Address 12-14 www.elanhomesystems.com...

  • Page 3: Introduction

    The following guide is a step-by-step instruction on how to connect and configure your Cisco SG300 Layer 3 Managed network switch. Cisco feature requirements The following features need to be enabled on the Cisco network switch:- 1. Layer 3 mode 2. Jumbo Frame 3.

  • Page 4: Connecting To The Web Gui Interface

    In order to connect to the network switch your computer will need to be physically connected to the Cisco switch using a Ethernet network cable. The computer must also be in the same IP range as the Cisco switch default IP address. If you are unsure how to update your computer IP range follow the ‘Changing your computer IP address’...

  • Page 5: Activating Layer 3 Mode

    Cisco SG300 SETUP GUIDE Activating Layer 3 mode The first setting you MUST update is to turn the network switch to Layer 3 mode. This must be completed before all other setting changes are made as this will default the factory settings when Layer 3 is activated.

  • Page 6: Jumbo Frames

    Cisco SG300 SETUP GUIDE Jumbo Frame To enable Jumbo Frame, Under ‘Port Management’ menu Select ‘Port settings’ Tick ‘ENABLED’ checkbox adjacent to Jmubo Frames tick ‘ J umbo Frame’ checkbox under Port Settings Click ‘Apply’ to update the setting www.elanhomesystems.com...

  • Page 7: Igmp Snooping

    Cisco SG300 SETUP GUIDE IGMP Snooping To enable IGMP snooping, there are several steps required to enable this feature:- • Bridge Video Over IP Filter Status • IGMP Snooping Status • IGMP Querier Status • MRouter Ports Auto Learn •...
  • Page 8 Cisco SG300 SETUP GUIDE IGMP Snooping - IGMP Snooping Status Under ‘Video Over IP’ menu Select ‘IPv4 Video Over IP Configuration’ Select ‘IGMP Snooping’ Tick ‘Enabled’ checkbox adjacent to IGMP Snooping Status Tick ‘Enabled’ checkbox adjacent to IGMP Query Status Confirm other settings match those as shown in the above image Click ‘APPLY’...

  • Page 9: Igmp Snooping

    Cisco SG300 SETUP GUIDE IGMP Snooping - IGMP Query Status, Mrouter ports auto learn, Immediate leave & IGMP querier election Under ‘Video Over IP’ menu Select ‘IPv4 Video Over IP Configuration’ Select ‘IGMP Snooping’ Select Line 1 in the IGMP Snooping table and click the ‘EDIT’ button the following pop-up window will appear Tick ‘Enabled’...

  • Page 10: Turning On/Off Poe

    SETUP GUIDE Turning On/Off POE Not all Cisco SG300 switches support POE. Those network switches that do support POE come with this as factory default to ‘ON’ . If you are unsure of the port setting please follow the below instructions.

  • Page 11: Apply And Save Settings

    Cisco SG300 SETUP GUIDE Apply and Save settings All settings that have been previously updated will not be finalised until the configuration is saved and the switch is rebooted. To save the configuration: Under ‘Administration menu Select ‘File Management’ Select ‘Copy/Save Configuration’...

  • Page 12: Changing Your Computer Ip Address

    Cisco SG300 SETUP GUIDE Changing your computer IP address to communicate with the Cisco network switch 1) Connect your computer to your network switch using Ethernet cable 2) In the Windows toolbar navigate to ‘CONTROL PANEL’ 3) Select ‘NETWORK AND INTERNET’...
  • Page 13 Cisco SG300 SETUP GUIDE 7) In the next window select ‘PROPERTIES’ 8) A. In the ‘NETWORKING’ window highlight/select ‘INTERNET PROTOCOL VERSION 4 (TCP/IPv4) B. Select ‘PROPERTIES’ contact techsupport@elanhomesystems.com...
  • Page 14 9) A. Under the ‘General’ tab select ‘USE THE FOLLOWING IP ADDRESS’ B. Enter the following FIXED IP network details 10) Click ‘OK’ and exit the network setup 11) Enter the default Cisco IP address in your web browser and check that you can connect to the unit. www.elanhomesystems.com...
  • Page 15 www.elanhomesystems.com...

Table of Contents