IC031 Magnetic Belt Drive Performance Indoor Cycle Bike USER MANUAL IMPORTANT: Read all instructions carefully before using this product. Retain owner’s manual for future reference. For customer service, please contact: service@zoovaa.com...
IMPORTANT SAFETY INFORMATION Please read these instructions very carefully before using this item. Note the following precautions before assembling or operating the equipment. 1. Keep children and pets away from the equipment at all times. Do not leave unattended children in the same room with the equipment. 2.
Page 7
ASSEMBLY INSTRUCTIONS PREPARATION A. Before assembly, make sure that you will have enough space around the item and you have all the parts. B. We recommend having 2 people to do the assembly. ASSEMBLY INSTRUCTIONS: STEP 1: Attach the Front Stabilizer (No.8) and the Rear Stabilizer (No.2) to the Main Frame (No.1) using 4 Flat Washers (No.5), 4 Domed Nuts (No.6) and 4 Carriage Bolts (No.3).
Page 8
STEP 2: Insert the Vertical Seat Post (No.12) into the Main Frame (No.1) and set at desired height. Insert and tighten the Adjustment Knob (No.10). Attach the Seat Slider (No.15) to the Vertical Seat Post (No.12) using the Adjustment Knob (No.86) and the Flat Washer (No.85). Unscrew Hexagonal Nut (No.87).
Page 9
STEP 3: Insert the Handlebar Post (No.17) into the Main Frame (No.1). Set at desired height, then insert and tighten the Adjustment Knob (No.10). Attach the Handlebar (No.18) to the Handlebar Post (No.17) using the Adjustment Knob (No.13) and the Flat Washer (No.14). NOTE: Make sure the Adjustment Knob (No.13) is tightened.
Page 10
STEP 4: Note: The Pedals (No.27L & No.27R) are marked "L" and "R" for Left and Right. Make sure you attach the correct pedal to the corresponding crank. Attaching the pedal to the wrong crank could irreversibly damage both the pedal and the crank. Attach Left Pedal (No.27L) to Left Crank (No.29).
TENSION ADJUSTMENT A. Adjusting the Tension: Increasing or decreasing the tension allows you to add variety to your workout sessions. To increase the tension, rotate the Brake Knob (No.49) clockwise. To decrease the tension, turn the Brake Knob (No.49) counter-clockwise. B.
SEAT AND HANDLEBAR ADJUSTMENT The seat of this bike is fully adjustable as it moves Up, Down, Forward, Backward. A. To adjust the height of the Vertical Seat Post (No.12), loosen and pull on the Adjustment Knob (No.10), then raise or lower the seat to the desired height. Once adjusted, re-insert and tighten the Adjustment Knob (No.10) to secure the seat in place.
BALANCE ADJUSTMENT To achieve a smooth and comfortable experience, you must ensure that the bike is stable. During use, if you notice that the bike is unbalanced, you can adjust the Base Levelers (No.7) located beneath the Front and Rear Stabilizers (No.2 and 8). To adjust, use the crosshead spanner to loosen the Hexagonal Nut (No.87) by turning it clockwise.
BELT TENSION ADJUSTMENT If you feel slippage when pedaling, the belt may need to be tightened. This may happen after a long period of use. To tighten the belt, loosen Hexagonal Nut (No.87) counter clockwise, turn Bolt (No.82) clockwise to tighten, then tighten Hexagonal Nut (No.87) clockwise. Try turning the crank to see if the belt runs smoothly.
HOW TO MOVE THE BIKE Firmly grasp and hold each side of the Handlebar (No.18). Place one foot on the front base and tilt the bike towards you until the transport wheels on the front base touch the ground. With the wheels on the ground, you can transport the bike to the desired location with ease.
COMPUTER INSTRUCTIONS KEY FUNCTIONS: MODE: Press to select a function. SET: Press to preset value for TIME, DISTANCE, CALORIES. CLEAR (RESET): Press to clear the value. HOW TO USE: The computer can either: (1) count the values for this workout session (2) countdown from a preset value for TIME, DISTANCE, CALORIES) To turn on the computer, start pedaling or press any key.
RESET: To reset values to zero, press and hold the MODE key for 3 seconds. This does not reset ODOMETER.If you change the batteries, all values will reset to 0, including ODOMETER. BATTERY: The computer uses 2 AAA batteries, which are included. If there is a problem with the display, try changing the batteries first.
Need help?
Do you have a question about the IC031 and is the answer not in the manual?
Questions and answers