Roland Super Jupiter MKS-80 Owner's Manual page 5

CONTENTS
[fj
Panel Description
3
A.
Front Panel 3
B.
Rear Panel 3
l2j
Connection 6
J3]
Operation
7
A. Outline of the IVIKS-80 7
B.
Play
Mode
8
a.
MIDI
Channel
Setting
8
b.
MIDI
Function Switch 8
c.
Tone
Color Selection 9
1)
Calling
a
Patch
Preset
10
2)
Calling
a
Tone
Memory
10
d.
Auto Tune
13
e.
Volume 13
f.
Dynamics
Sens
Knob
13
g.
Contrast
Knob
13
C.
Edit
Mode
(I)
14-20
a.
Parameters of
Tone Memory
Section ... 14
b.
Editing a
Tone Memory
21
c.
Parameters of Patch Preset Section
. . .
22—25
d.
Editing
a
Patch Preset
26
D. EditlVIode
(II)
27
a.
Setting
up
the
Programmer
MPG-80
.... 27
1)
Programmer Connector 27
2)
Connection
27
b.
How
to use the
Programmer
MPG-BO
...
28
1
)
Method
1
28
2!
Method
2
29
E.
Write
Mode
30
a.
Writing
a
Tone
Memory
30
b.
Writing a Patch Preset 31
F.
Memory
Cartridge
32
a.
Saving
onto
the
Memory
Cartridge 32
b.
Loading
from
the
Memory
Cartridge
... 34
g]
MIDI
36
A. Saving and Loading
36
a.
Saving the data
in
the
MKS-BO
to
a
MIDI
device
(or
computer} 37
b.
Loading
the data
in
the
MIDI
device
(or
computer)
to the
MKS-80
39
B.
Indicators
40
a.
Receive
Mode
Indicators
40
b.
MIDI
Message indicators 40
[5]
Tables 41
Edit
Map
11
Parameter Table
41
Display Message Table 44
Program Change
Table
45
MIDI Function Table 46
\6\
Specifications 47
IMPORTANT NOTES
Before turning the
MKS-80
on,
make
sure that
the Protect
Switch
®
is
set
to the
ON
position.
Otherwise the data
in
memory may
be destroyed.
Power Supply
Location
• The
appropriate voltage to be used
is
shown on
the name
piate
on the
rear panel. Be sure that
it
meets
the voltage
system
in
your
country.
• Do
not use the same socket
that
is
used
for
any
noise generating device,
such
as a
motor,
or varia-
ble lighting system.
•
When
setting
up
the
MKS-80,
be sure that
all
the
units are turned
off.
•
This
unit
might not
work
properly
if
turned
on
immediately
after
turned
off, or
if
the
power
cable
is
plugged
in
with
the unit turned on.
If
this
happens, simply turn the
unit off,
and
turn
it
on
again
in a
few seconds.
•
Operating the
MKS-80
near
a
neon
or fluorescent
lamp
may
cause
noise interference.
If
so,
change
the angle or position of the
MKS-80.
• Avoid
using the
MKS-80
in
extreme heat or
humidity
or
where
it
may
be
affected
by
dust.
Cleaning
•
Use
a
soft cloth
and
clean on!y with
a
mild
detergent.
•
Do
not use solvent-such as paint thinner.
• This
unit
might get
hot
while operating, but
there
is
nothing to
worry
about.