Table of Contents
Advertisement
Quick Links
• This product is not intended for life or safety applications.
This product is not intended for installation in hazardous or classified
locations.
• Potential electrocution hazard exists. Installing sensors in an
energized motor control center or on any energized conductor can be
hazardous.
• Read instructions thoroughly prior to install
Severe injury or death can result from electrical shock during contact with
high voltage conductors or related equipment. Disconnect and lock-out
all power sources during installation and service. Applications shown are
suggested means of installing sensors, but it is the responsibility of the
installer to ensure that the installation is in compliance with all national
and local codes. Installation should be attempted only by individuals
familiar with codes, standards, and proper safety procedures for high-
voltage installations.
Z102662-0C
Installation Instructions
H8932, H8936
Network Display
VERIS INDUSTRIES
PORTLAND, OREGON USA
(503) 598-4564 FAX (503) 598-4664
http://www.veris.com
Comprehensive Power Monitoring Display
Monitor critical parameters with one networked display
Supports a variety of sensors
• H8035/6 Enercept Power Meters
• H704-42 Branch Current Monitors
• H663 Branch Current Monitors
• H8238 Multi Circuit Monitors
• H8160 Series Energy Meter
Membrane switch buttons provide convenient setup and viewing of
data from all devices on the power monitoring network
Pass through communications to other Modbus devices
Presents System Data Visually and to a Network
Large backlit LCD...easy to read
Palm OS Infrared interface...instantly upload data from all
Veris devices to a palm pilot, or use a Modbus network
Modbus protocol communications, one digital input standard
Upstream communications selectable RS485, RS232, or infrared
Multi color LED...provides quick system status
OPERATION
The H8932/H8936 Network Display provides local indication of power system
parameters from Veris devices. To report critical alarm data the H8932/H8936
is equipped with a digital alarm input and local alarm annunciation.
All system variables and alarms can be passed to the network operations
center by means of Modbus RTU protocol. In the event that the network
operations center is not yet established, the data can be uploaded to a Palm
Pilot through the IR communications port located on the front of the display.
-1-
1-800-354-8556
email:sales@veris.com
®
Advertisement
Table of Contents
Related Manuals for Hawkeye Mfg H8936
Summary of Contents for Hawkeye Mfg H8936
-
Page 1: Installation Instructions
The H8932/H8936 Network Display provides local indication of power system parameters from Veris devices. To report critical alarm data the H8932/H8936 is equipped with a digital alarm input and local alarm annunciation. All system variables and alarms can be passed to the network operations center by means of Modbus RTU protocol. -
Page 2: Component Locations
COMPONENT LOCATIONS BACK FRONT Figure 1 250 VAC 200mA Slow Blow Fuse Upstream RS485 Connection Point Fused power connection for circuit protection. 5-position Euro style pluggable connector for upstream RS-485 network. 2 or 4-wire selectable. Lithium Battery Downstream RS485 Connection Point On board clock back up. -
Page 3: Physical Installation
H8930 Component List: A. Face Plate with membrane switch ribbon cable B. Four threaded stand-offs C. Network Display D. Four #6-32 screws H8936 Assembly Example: BOX LID or PANEL NETWORK DISPLAY FACEPLATE (A) (4 ea.) THREADED STAND OFFS (B) NETWORK DISPLAY (C) (4 ea.) #6-32 SCREWS (D) -
Page 4: Network Configuration
Communications Wiring The H8932/H8936 resides on a Modbus network as a pass-through device. Unlike most Modbus RTU devices it is not wired in a daisy chain configuration. Instead make an upstream and downstream communication connection. This allows for flexible data retrieval as the upstream options include RS232, RS485, or Palm Handheld compatible IR. -
Page 5: Electrical Installation
ELECTRICAL INSTALLATION Wiring 1. Connect upstream RS485 or RS232 if used. Infrared communications will not function with upstream connection enabled. To enable infrared, leave Upstream RS485 and RS232 port connections disabled. 2. Connect downstream RS485 device daisy chain. 3. Make power connection. Use either 120 VAC 2-wire or 12VDC as shown below. Power Wiring Option #1 120 VAC Power Wiring Option #2*... -
Page 6: Setup Mode
ELECTRICAL INSTALLATION Terminating the Last Device in the Downstream Daisy chain Terminate the Downstream network per the RS485 standard to ensure reliable communications. SETUP Setup Mode Setup mode is used to initialize and configure the display to the application requirements. Sub-menus are used to group parameters for setup. -
Page 7: Setup Communications
SETUP Setup Mode Sub Menus 1. SETUP COMMUNICATIONS 3. FIND METERS Select SETUP COMMUNICATIONS to adjust communications parameters. Selecting FIND METERS initiates a search and identifies devices on the network. Exit the search by pressing any key (do not exit until all active addresses have been counted). -
Page 8: Monitoring Mode
Monitoring is the default mode for the H8932/H8936. In monitoring mode, parameters of all supported devices are displayed and updated on a 4 second interval. The H8932/H8936 may be set up to automatically cycle through all parameters on all devices on the network, or display a selected parameter continuously. - Page 9 QUICK REFERENCE MENU TREE MONITORING �� ���� ������ ����� ���������� �������������� ������������ ������ ��������� ��������� ���������� ���������� �������� ����� ������ ����� ����� �� ������ ����� ��������� ����������� ��������� ����� ���������� ����������� �������� ����� �� ���� �������������� �������������� ������������������������������������ ����� �� ����...
-
Page 10: Specifications
Duplex is UI-selectable 2-wire or 4-wire 5-position Euro style pluggable connector RS-232 ..................... DCE, no handshaking DB-9 connection: pin 2: Transmitted Data from H8936 pin 3: Received Data into H8936 pin 5: Ground Infrared ................... Infrared port located above STATUS LED Bi-directional (transmit and receive) 875nm, 30-degree viewing angle, 12”... - Page 11 SPECIFICATIONS Status (Tri-color) Green = Normal Operation. No network devices are in warning or alarm mode. Yellow = Warning. One or more network devices are in warning mode. Red = Alarm. One or more network devices are in alarm mode or the auxiliary input is active. Supported Modbus Devices Enercept Full-Data-Stream Power Meter (H8036) Enercept Energy-Only Power Meter (H8035)
Need help?
Do you have a question about the H8936 and is the answer not in the manual?
Questions and answers