Philips DFR9000 Service Manual page 12

7. DAB bit error rate test
Purpose: Reads and displays the bit error rate of the DAB
tuner.
MAIN MENU
RC "7"
N
pressed?
Y
DAB Bit Error
Rate Test
tune to first station
in the DAB
data base
display
"ffff.fff" + " rrr.rr" or
" " + "NO VALUE"
RC "OK"
Y
pressed?
N
RC
Y
"RIGHT"
pressed?
N
RC "7"
Y
pressed?
N
display
" SCAN "
scan band III and L
Notes: "rrr.rr" is the bit error rate in %.
"NO VALUE" is shown if no station is available. In
this case connect antenna or the test signal and
press the DAB ErrorBitRate button again. The
module will scan band III and the L band for stations
(about 2 minutes) and tune to the first station found.
It is possible to set the DAB module to a defined
center frequency. Press "RIGHT" on the RC and
229.072 MHz center frequency (228.304 till 229.840
with block name 12D) will be selected. Use "RIGHT"
and "LEFT" to select another frequency. Press the
DAB ErrorBitRate button to tune to the frequency.
clear DAB data base
set frequency to
229.072MHz
display frequency
"ffff.fff"
RC
"LEFT" Y
dec. freq.
pressed?
N
RC
Y
"RIGHT"
inc. freq.
pressed?
N
RC "7"
N
pressed?
Y
display
" SCAN "
scan frequency
2-7
7. Audio switch test
Purpose: Switches several audio modes according to the
table below. System related limitations are
ignored.
MAIN MENU
RC "8"
N
pressed?
Y
Video Switch
Test
Display audio
mode
(see table 3)
RC "OK"
Y
pressed?
N
RC "8"
pressed?
Select next
audio mode
(see table 3)
A u d o i m o d e
M u t l c i h a n n l e
A n a o l g 1
A n a o l g 2
A n a o l g 3
A n a o l g 4
A n a o l g 5
A D C e t t s
T e t s o t n e g e n r e t a r o L
T e t s o t n e g e n r e t a r o C
T e t s o t n e g e n r e t a r o R
T e t s o t n e g e n r e t a r o S R
T e t s o t n e g e n r e t a r o S L
T e t s o t n e g e n r e t a r o S U B W
T e t s o t n e g e n r e t a r o L d o w n m x i
T e t s o t n e g e n r e t a r o R d o w n m x i
C o a x 1
C o a x 2
C o a x 3
O p c i t l a
Notes: All DAC/CODEC outputs are routed to amplifiers/line
out sockets. If connecting ADC data output to all data
inputs of CODEC/DAC in parallel, input signal to
ADC will show on all outputs.
The test starts with -30dB as volume setting.
VOLUME (at least rotary) will work setting the
volume level. BASS/TREBLE will be 0dB (not
changeable). The routing will be influenced by HP
connect (HP out instead of LS). Line out and record
out is always active (L+R).
D e s c i r t p o i n
L n i k m u t l c i h a n n l e n i p u s t o t h t e o l u d s p e a k r e
i w h t o t u u s n i g h t e D S ; P l l a a m p f i l e i s r a e r
e n a b e l ; d l l a m t u n i g u f n t c o i n s a e r d s i a b e l d
L n i k h t e u t n r e o t h t e o u p t t u
L n i k T V n i o t h t e o u p t t u
L n i k F o r t n n i
L n i k D V D n i
L n i k G a m e n i
L n i k G a m e n i b t u u s e h t e D S P A ( D C - D A C )
U s e e t t s o t n e g e n r e t a r o o n h t e V P B i w h t 4 4 0 H
U s e e t t s o t n e g e n r e t a r o o n h t e V P B i w h t 4 4 0 H
U s e e t t s o t n e g e n r e t a r o o n h t e V P B i w h t 4 4 0 H
U s e e t t s o t n e g e n r e t a r o o n h t e V P B i w h t 4 4 0 H
U s e e t t s o t n e g e n r e t a r o o n h t e V P B i w h t 4 4 0 H
U s e e t t s o t n e g e n r e t a r o o n h t e V P B i w h t 4 4 0 H
U s e e t t s o t n e g e n r e t a r o o n h t e V P B i w h t 4 4 0 H
U s e e t t s o t n e g e n r e t a r o o n h t e V P B i w h t 4 4 0 H
U s e d i g i a t i l , n d e c o d e f i D D r o D T S a n d
t a r n f s r e o t h t e o l u d s p e a k r e
U s e d g i t i l a n i
U s e d g i t i l a n i
U s e d g i t i l a n i
S a t t r a g a n i i w h t i f s r i t e t m
D s i p a l y
M _ C H N I
T U N E R N I
T V N I
C A M N I
D V D N I
G A M E N I
A D C N I
z L E F T
z C E N T E R
z I R G H T
z R E A R R
z R E A R L
z S U B W
z D O W N L
z D O W N R
C O A X 1 N I
C O A X 2 N I
C O A X 3 N I
O P T N I