Hanyoung HX4 Instruction Manual page 7

HX communication - instructions about the D register address
D-register Parameter
Parameter meaning
address name
0001 NPV Current present value (PV)
0002 NSV Current set value (SV)
0004 SSV Current set value (SV)
OUT1 control output value of standard type, Total
0005 MVOUT
control output value of heating/cooling type.
OUT1 control output value of standard type,
0006 CH1OUT OUT1 control output value of heating/
cooling type.
OUT2 control output value of heating/
0007 CH2OUT
cooling type.
When ZONE is OFF, currentlly
applied set value (SV) and PID group
number
0001: SV1, PID group 1
0002: SV2, PID group 2
0008 PIDNO 0003: SV3, PID group 3
When ZONE is OFF, currentlly
applied PID group number
0001: PID group 1
0002: PID group 2
0003: PID group 3
Current state of Alarm 1 and Alarm 2:
0000: Alarm 1 OFF, Alarm 2 OFF
0009 ALMSTS 0001: Alarm 1 ON, Alarm 2 OFF
0002: Alarm 1 OFF, Alarm 2 ON
0003: Alarm 1 ON, Alarm 2 ON
When the OUT2 control output is SCR
(4-20mA) in Heating / Cooling type,
0013 OUT2_IND
it shows the temperature controller
"OUT2 indicator" status.
Current measurement value of the
0014 H1CM
heater break alarm output
Current situation of the AD error.
0016 ADESTS
0001: AD conversion error
Current situation of the input error.
0001:Input sensor Burn-out
0017 ERRSTS 0002: RJC error
0004: Input range exceeded
0008: Less than input range
Autotuning (AT) current state
0000: AT type
0018 AT_STS 9999: AT in progress ("AT indicator" in
the temperature controller front display
blinking)
Zone function set (For the zone position
0102 ZONE
setting, set in RP parameter of each PID group
0104 ARW ARW (Anti-reset windup) setting
0106 DI.SL External contact input (DI) function
0107 ALPHA Alpha factor of 2 DOF PID
0108 UP.RT Ramp-up temperature setting
0109 DN.RT Ramp-down temperature setting
0110 RTMU Ramp-time unit setting
0111 UPTM Ramp-up time setting
0112 DNTM Ramp-down time setting
0113 RAMPT Ramp type selection
Manual output function (when selecting
0120 MVMOD the manual output, the "AT indicator" in the
temperature controller front display is steady)
0121 MANMV Manual output value (Manual MV) set 0 ~ 100 %
0122 CTRM Control mode selection
0124 HKSL Hot-key selection
0300 SVNO Set value (SV) number selection
0301 SV1 Set value 1 (SV) setting
0302 SV2 Set value 2 (SV) setting
0303 SV3 Set value 3 (SV) setting
0305 AT MODE Auto-tuning (AT) type selection
0306 AT Auto-tuning (AT)
0310 1.P PID group 1 proportional band
0311 1.I PID group 1 integral time
0312 1.D PID group 1 derivative time
0313 1.MR PID group 1 manual reset
0314 1.PC PID group 1 cooling proportional band 0.0 ~ 999.9 %
0315 1.IC PID group 1 cooling integral time
0316 1.DC PID group 1 cooling derivative time
0317 1.DB PID group 1 Heating / Cooling dead band -100.0 ~ 50.0 %
0318 1.RP PID group 1 zone position setting
0320 2.P PID group 2 proportional band
0321 2.I PID group 2 integral time
0322 2.D PID group 2 derivative time
0323 2.MR PID group 2 manual reset
0324 2.PC PID group 2 cooling proportional band 0.0 ~ 999.9 %
0325 2.IC PID group 2 cooling integral time
0326 2.DC PID group 2 cooling derivative time
0327 2.DB PID group 2 Heating / Cooling dead band -100.0 ~ 50.0 %
0328 2.RP PID group 2 zone position setting
0330 3.P PID group 3 proportional band
0331 3.I PID group 3 integral time
0332 3.D PID group 3 derivative time
0333 3.MR PID group 3 manual reset
Parameter
Parameter setting
division
Read only *1 Process
Read only *1 Process
Read only *1 Process
*2
Read only Process
*2
Read only Process
Read only *2 Process
Read only Process
Read only Process
Read only Process
Read only Process
Read only Process
Read only Process
Read only Process
0: OFF, 1: ON Control Group
0: AUTO, 50.0 ~ 200.0 % *2 Control Group
0: OFF, 1: ON Control Group
0 ~ 100 % Control Group
0: OFF / EUS(0~100 %) *1 Control Group
0: OFF / EUS(0~100 %) *1 Control Group
0: Hour, 1: Min Control Group
0.01 ~ 99.59 [hh.mm] *2 Control Group
0.01 ~ 99.59 [hh.mm] *2 Control Group
0: A Type, 1: B Type Control Group
0: AUTO ,
Control Group
1: MANUAL
Control Group
0: Traditional,
Control Group
1:2 2 DOF PID (2DOF)
0: Auto-tuning (AT) function
Control Group
1: Manual output function
1 ~ 3 Set value setting group
EU(0 ~ 100 %) *1
Set value setting group
EU(0 ~ 100 %) *1 Set value setting group
EU(0 ~ 100 %) *1 Set value setting group
0: Standard Automatic Operation
1: Low value (PV) type Auto-tuning Group
automatic operation
0: OFF, 1 ~ 4 Auto-tuning Group
0.0 ~ 999.9 % *2 PID Group
0 ~ 6000 sec PID Group
0 ~ 6000 sec PID Group
-5.0 ~ 105.0 % *2 PID Group
*2 PID Group
0 ~ 6000 sec PID Group
0 ~ 6000 sec PID Group
*2 PID Group
EU(0 ~ 100 %), (1.RP < 2.RP) *1 PID Group
0.0 ~ 999.9 % *2 PID Group
0 ~ 6000 sec PID Group
0 ~ 6000 sec PID Group
-5.0 ~ 105.0 % *2 PID Group
*2 PID Group
0 ~ 6000 sec PID Group
0 ~ 6000 sec PID Group
*2 PID Group
EU(0 ~ 100 %), (1.RP < 2.RP) *1 PID Group
0.0 ~ 999.9 % *2 PID Group
0 ~ 6000 sec PID Group
0 ~ 6000 sec PID Group
-5.0 ~ 105.0 % *2 PID Group
D-register Parameter
Parameter meaning
address name
0334 3.PC PID group 3 cooling proportional band 0.0 ~ 999.9 %
0335 3.IC PID group 3 cooling integral time
0336 3.DC PID group 3 cooling derivative time
PID group 3 Heating / Cooling dead
0337 3.DB
band
0400 HBA Heater break alarm (HBA) current set 0: OFF, 1 ~ 50 A
Heater break alarm (HBA) Hysteresis
0401 HDB
(deadband) set.
0410 A1TY Alarm 1 type setting
0411 A2TY Alarm 2 type setting
0413 A1DB Hysteresis (dead band) of alarm 1
0414 A2DB Hysteresis (dead band) of alarm 2
0416 AL-1 Set value of alarm 1
0417 AL-2 Set value of alarm 2
0500 RET Retransmission output type selection
0501 RET.H Retransmission output upper limit setting -1999 ~ 9999
0502 RET.L Retransmission output lower limit setting -1999 ~ 9999
0503 RET.T Retransmission output form
0600 OUT Output type selection
0601 o.ACT Output operation selection
0602 CT Cycle type (Control cycle)
0603 CTC Cooling cycle type (cooling control cycle) 1 ~ 1000 sec
General type. ON/OFF control hysteresis Standard type,EUS(0~100%) *1
0604 HYS
Heating / Cooling type.
ON/OFF control hysteresis
0605 PO Output1 setting when input breaks
0606 POC Output2 setting when input breaks
0607 OL-H Output upper limit function
0608 OL-L Output lower limit function
0610 INP Input type selection
0611 UNIT Temperature unit selection
0612 FR-H Upper range selection
0613 FR-L Lower range selection
Decimal point position selection
0614 DP-P
during the voltage input)
Scale upper limit setting
0615 SL-H
(during voltage input)
Scale lower limit setting
0616 SL-L
(during voltage input)
0617 FILT Measurement value filter selection
0618 BIAS Measurement value correction setting EUS(-100 ~ 100%)
0619 B.OUT Operation selection when input breaks 0: OFF, 1: UP, 2: DOWN
0624 HYST Hysteresis type
*1: Please check the presence or absence of the decimal points according to the
input type and range settings
· Set value with decimal points : if you want to input an SV1 of 100.0℃ through
communication, transmit 03E8(100). (03E8 is the hex value of 1000)
· Set value without decimal points: if you want to input an SV1 of 100℃ through
communication, transmit 0064(100). (0064 is the hex value 100)
*2 : Set value with decimal places.
※ For the instructions of the protocol regarding communication, please refer to the
Hanyoung protocol instruction manual on Hanyoung Nux homepage(www.hynux.com).
How to dismantle case
● HX4
-7-
Parameter setting
*2
0 ~ 6000 sec
0 ~ 6000 sec
-100.0 ~ 50.0 % *2
0 ~ 50
0: OFF, 1 ~ 21
0: OFF, 1 ~ 21
EUS(0 ~ 100 %)
EUS(0 ~ 100 %)
PV al a rm: EU (-100 ~ 100 %) *1 Alarm Group
Devi a ti o n al a rm: EUS (-100 ~ 100 %)
0: Indicated value
1: Set value (SV)
2: Control output value (MV)
3: Power SPS for the sensor
0: 4 - 20 mA, 1: 0 - 20 mA
0~12 (refer to the number of
control output type selection)
0: Reverse operation (heating),
1: Direct action (cooling)
1 ~ 1000 sec
Heating / Cooling type *2
0 ~ 10.0%
-5.0~105.0% *2 Output group
0~105.0% *2 Output group
Standard type, *2
OL-L +1 digit ~ 105.0 %
Heating / Cooling type,
0.0 ~ 105.0 %
Standard type, *2
-0.5 % ~ OL-H-1 digit
Heating / Cooling type,
0.0 ~ 105.0 %
1~31
0: ℃, 1: ℉
EU(0 ~ 100 %) *1
EU(0 ~ 100 %) *1
0: No decimal points
1: 1 decimal place
2: 2 decimal places
3: 3 decimal places
-1999 ~ 9999
-1999 ~ 9999
0: OFF, 1 ~ 120 sec
*1
0: CENTER ,
1: EDGE
● HX2 ● HX3
● HX7 ● HX9
Parameter
division
PID Group
PID Group
PID Group
PID Group
Heater break
alarm group
Heater break
alarm group
Alarm Group
Alarm Group
Alarm Group
Alarm Group
Alarm Group
Retransmission
group
Retransmission
group
Retransmission
group
Retransmission
group
Output group
Output group
Output group
Output group
Output group
Output group
Output group
Input group
Input group
Input group
Input group
Input group
Input group
Input group
Input group
Input group
Input group
Output group