Specifications - Sharp XV-Z200U Service Manual

Product type Projector
Models XV-Z200U/DT-300/XV-Z200E/XV-Z201E
Video system PAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSC 4.43
DTV 480I/480P/720P/1080I/576I/576P
Display method DLP chip, RGB optical shutter method
DLP panel Panel size: 0.6
Display method: Single Panel Digital Micromirror Device (DMD™) by Texas Instruments
Drive method: Digital Light Processing (DLP™)
No. of dots: 589,824 dots (1,024 [H]
Lens 1–1.2
Projection lamp 210 W/168 W SHP lamp
RCA Connector: VIDEO (INPUT 4), composite video, 1.0 Vp-p, sync negative, 75 Ω terminated
Video input signal
S-video input signal 4-pin Mini DIN connector (INPUT 3)
Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated
C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated
Component input signal RCA Connector
Y: 1.0 Vp-p, sync negative, 75 Ω terminated
(INPUT 1)
: 0.7 Vp-p, 75 Ω terminated
P
B
: 0.7 Vp-p, 75 Ω terminated
P
R
Component input signal 29-pin connector
DVI input signal: Digital 250–1,000 mV 50 Ω
(INPUT 2)
Y: 1.0 Vp-p, sync negative, 75 Ω terminated
: 0.7 Vp-p, 75 Ω terminated
P
B
: 0.7 Vp-p, 75 Ω terminated
P
R
Horizontal resolution 520 TV lines (NTSC 3.58 input)
RGB input signal DVI-I terminal
<Digital>
Input impedance 50 Ω
<Analog>
Input impedance 75 Ω
<Synchronization signal>
• Separate sync/Composite sync
Input level TTL level
Input impedance 1 KΩ
• Green on sync
Input level (Synchronizing input) 0.286 Vp-p
Input impedance 75 Ω
Pixel clock 12–80 MHz
Vertical frequency 43–75 Hz
Horizontal frequency 15–70 kHz
Computer control signal 9-pin D-sub connector (RS-232C Port)
Rated voltage AC 100–240 V
Input current 3.2 A
Rated frequency 50/60 Hz
Power consumption 285 W
Heat dissipation 1,070 BTU/hour
Operating temperature 41°F to 95°F ( 5°C to 35°C)
Storage temperature 4°F to 140°F ( 20°C to 60°C)
Cabinet Plastic
I/R carrier frequency 38 kHz
Dimensions (approx.) 14 1 ⁄
2
14 1 ⁄
2
Weight (approx.) 10.1 lbs. (4.6 kg) (including swivel stand) 9.0 lbs. (4.1 kg) (main body only)
Supplied accessories Remote control, Two AA size batteries, Power cord, Terminal cover, Lens cap (attached
on the body), Operation manual, Screws for terminal cover, 21-pin RCA conversion adaptor, Video cable
Replacement parts Lamp unit (Lamp/cage module) (BQC-XVZ200++1), Remote control
(RRMCGA218WJSA), AA size batteries, Power cord (QACCDA007WJPZ:SEC/SECL, QACCV4002CEZZ:
SEEG/SEI, QACCBA012WJPZ:SUK/SRS/SRH/SEEM, QACCLA018WJPZ:SCA/SNZ), Terminal cover
(GCOVAA116WJKB), Lens cap (CCAPHA004WJ01), Operation manual (SEC/SECL:TiNS-B005WJZZ
(XV-Z200U/E)/TiNS-B006WJZZ (XV-Z201E, DT–300), SEEG/SUK:TiNS-B007WJZZ (XV-Z200U/E)/TiNS-
B009WJZZ (XV-Z201E, DT–300), SCA/SNZ/SRS/SRH/SEEM/SEI:TiNS-B008WJZZ (XV-Z200U/E)/TiNS-
B010WJZZ (XV-Z201E, DT–300)), Screws for terminal cover (XBBSN40P10000), 21-pin RCA converter
adaptor (QSOZ0361CEZZ:SEEG/SUK), Video cable (QCNWGA001WJZZ))
This SHARP projector uses a DMD chip. This very
sophisticated chip contains 589,824 pixels. As with any high
technology electronic equipment such as large screen TVs,
video systems and video cameras, there are certain
acceptable tolerances that the equipment must conform to.
Specifications are subject to change without notice.

SPECIFICATIONS

576 [V])
zoom lens, F1.75–2.04 f=28.0–33.5 mm (XV-Z200U/E), F2.0–2.4 f=16.9–20.2 (XV-Z201E, DT–300)
Analog 0.7 Vp-p 75 Ω
Input level 250-1000 mV
Input level 0.7 Vp-p
× × ×
(W) 6 9 ⁄ (H) 12 7 ⁄ (D) (368
16 8
× × ×
(W) 4 5 ⁄ (H) 12 7 ⁄ (D) (368
8 8
This unit has some inactive pixels within acceptable
tolerances which may result in inactive dots on the picture
screen. This will not affect the picture quality or the life
expectancy of the unit. If you have any questions about this
matter, please call toll free 1-877-DTV-SHARP (1-877-388-
7427).
U.S.A. ONLY
3
×
153.8 327 mm) (including swivel stand)
×
118 327 mm) (main body only)
XV-Z200U/E, XV-Z201E
DT-300