Related Manuals for SSV Works GN-5K
Summary of Contents for SSV Works GN-5K
- Page 1 Disassembly, Wire and Amplifier Plate Installation Under Dash Subwoofer Installation Kick Panel Speakers Installation Cage Mount Speakers Installation MRB3 and Dash Kit Installation...
-
Page 3: Tools Needed For Installation
All SSV Works enclosures are covered by a limited lifetime warranty against defects in instructions completely before material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty installation to avoid possible injury, or against defects in material or workmanship. All SSV Works Speakers are covered by a damage to the accessory or vehicle. - Page 4 PANELS AND DASH DISASSEMBLY A. Remove all seats by releasing the handle behind each seat, B. Disconect the negative battery cable from the battery. push forward slightly while lifting up. C. Remove hood by turning locking pins and lifting up. D.
- Page 5 PANELS AND DASH DISASSEMBLY G. Use a panel removal tool to remove the center dash panel and center pocket. Disconnect all harness connectors attached to the center dash panel. H1. Using a panel removal tool, remove the two (2) push pins holding lower center panel cover located on the passenger side. Slide cover off. I1.
- Page 6 RUNNING AMP POWER CABLE & SPEAKER WIRE J. Unplug the rubber grommet located on the firewall. K. Unwrap the tape from rubber grommet and feed the power/ground wire for the Amp through the grommet as well as the rear speaker harness H1151.
- Page 7 AMP PLATE INSTALLATION OUTSIDE DASH VIEW INSIDE DASH VIEW Q. Remove the two (2) T30 torx screws and clips located at the bottom of the dash panel near the center console L. Unclip harness that runs along top cross bar of dash (holes will T.
- Page 9 All SSV Works enclosures are covered by a limited lifetime warranty against defects instructions completely before in material or workmanship. All SSV Works Electronics are covered by a limited 1 year installation to avoid possible injury, or warranty against defects in material or workmanship. All Kicker Speakers are covered damage to the accessory or vehicle.
- Page 10 A. For this step you will need the sub enclosure mounting plate as well as two (2) M5 B. Using a T25 torx driver and 8mm socket, tighten the screws, two (2) 8mm nuts and four (4) M5 washers. Place the mounting plate on the screws to secure the plate.
- Page 11 G. Using a ¼ drill bit, drill holes for mounting of the enclosure. H. Place enclosure in location for mounting. I. Line up the holes from the enclosure to the mounting plate and J. Use three (3) M6 screws & washers to hand tighten the use three (3) M6 screws and washers to mount the enclosure.
- Page 13 LEFT SIDE DRILL TEMPLATE 170-GN-UD10 DRILL TEMPLATE...
- Page 15 RIGHT SIDE- DRILL TEMPLATE 170-GN-UD10 DRILL TEMPLATE...
- Page 17 All SSV Works enclosures are covered by a limited lifetime warranty against defects instructions completely before in material or workmanship. All SSV Works Electronics are covered by a limited 1 installation to avoid possible injury, or year warranty against defects in material or workmanship. All Kicker Speakers are damage to the accessory or vehicle.
- Page 18 A. Cut out the INSIDE template (Driver/Passenger) along the cut B. Using a scribing tool, mark the center of the 3 drill points line. Position the template on kick panel above the foot rest illustrated on the template as shown on image B. making sure to line up arrows on template to the curves of the panel as seen on image A.
- Page 21 All SSV Works enclosures are covered by a limited lifetime warranty against defects in instructions completely before material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty installation to avoid possible injury, or against defects in material or workmanship. All SSV Works Speakers are covered by a damage to the accessory or vehicle.
- Page 22 A. From the rear of the center console, connect the B-H1150 harness and B. Make sure the speaker wire is away from any moving and sharp parts, route to the rear driver and passenger side from under the console. pull cable out from under the center console. D.
- Page 23 G. Tighten the 8mm bolts once you have the speaker pods in your H. Make your speaker connections. desired location. I. Using the provided zip ties tie down speaker wire alongside the roll cage. J. Connect the B-H1151 speaker harness to the amplifier...
- Page 25 All SSV Works enclosures are covered by a limited lifetime warranty against defects in instructions completely before material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty installation to avoid possible injury, or against defects in material or workmanship. All SSV Works Speakers are covered by a damage to the accessory or vehicle.
- Page 26 C. Place the bottom edge of the kit on dash. D. With both thumbs press the top corners until the kit snaps into place. E. Pull the MRB3 Power and Ground wires through the Rubber F. At the Bus Bar terminal located under the hood, unscrew the nut on the grommet and feed through to the power strip located on the right second position terminal and attach the black Ground wire.
- Page 27 Polaris General USB/AUX Input Port A. Unscrew and remove the plastic nut from the port. Make sure to B. Make sure all harness connectors are unplugged from the dash open the fuse holder and remove the fuse so the nut will fit through it. panel.
- Page 28 D. Unscrew the factory nut on the positive battery terminal. Install the 2 power cables to the screw on the postive battery terminal. Re-install the factory nut. THIS CONCLUDES THE INSTALLATION PROCESS. REPLACE ALL FACTORY PANELS AND SEATS. QUESTIONS? PLEASE CONTACT SSV WORKS AT 818-991-1778 OR EMAIL SUPPORT@SSVWORKS.COM © 2017 SSV Works, Oxnard, CA 93030 GN-5K Rev. B 11-14-17...
Need help?
Do you have a question about the GN-5K and is the answer not in the manual?
Questions and answers