Page 2
EC Declara on of Conformity Cengar. Ltd. Springfield Works, Saddleworth Road Halifax, England HX4 8LZ We the undersigned, declare under our sole responsibility that the following apparatus: ‐ Machine descrip on: Cengar Air Saw Machine Type: JSZ Is in conformity with the following relevant EC legisla on: Machinery Direc ve 2006/42/EC Atex Direc ve 94/ 9/EC Based on the following Harmonised Standards: EN13463‐1:2009 And therefore complies with the essen al requirements of those ...
Cengar Air Saw Model JSZ We recommend normal safe working prac ces should be followed as per the Health and Safety at Work Act, or the appropriate Na onal and State Laws. We recommend that eye protec on be worn SPECIFICATIONS Speed 400/600 strokes per minute Stroke 57 mm Air Consump on 0.168m /minute Air Pressure 5‐6 Bar Weight 5.5 Kgs. Length 448 mm. Height 141 mm. Width 54 mm. Vibra on Level averaged ...
Page 4
Saw blades are capable of causing serious injury Think safe Act safe Be safe LUBRICATION Use Cengar Green Oil with longer las ng coa ng proper es for best results. Cengar Green Oil is specially prepared to: ‐ Emulsify the water generally found in compressed air lines. Give perfect mist lubrica on. Remain fluid at the low working temperature of compressed air tools. Contains corrosion and oxida on inhibitors. Incorrect oils if used will soon “break down” forming a sludge which will slow and eventually stop the ac on of the saw. See maintenance details. ...
Connect the air supply, rest the blade on the material to be cut with the nosepiece firmly abu ed to the work piece, with forward hand pressure, to prevent judder. Allow the Cengar Saw to cut under its own weight, with just a slight downward hand pressure to keep the teeth engaged in the cut. It is not necessary to put ...
Page 8
3 Fit the Stiffer sealing ring on top of the elastic ring, Use some green oil to ease its passage over the piston. 4 Fit the pistons into the bores using a ring compressor, with a coa ng of Cengar Green oil, and ensure they slide smoothly over the full travel range. ...
Page 9
Fit the desired saw blade with the teeth uppermost Mount the machine on to the post of the clamp, by pulling back the plunger on the top of the saw, and sliding onto the post un l the plunger snaps back. Ensure the machine has locked on properly. When mounted correctly, the blade should be under the pipe, such that the weight of the machine applies the cu ng force to the blade. (Fig.2) Start the machine, locking on the trigger, and gently bring the blade into contact with the work, gradually release the weight of the machine and allow the cut to take place without extra force. If using a long blade for larger diameter pipes, the bow guide supplied can be used to ensure a straight cut is achieved. Once the blade has entered into the work enough to self support, the bow guide is no Fig. 2 Clamp CP 1 ...
Page 10
NEVER NEVER fit breakable “All‐Hard” blades in Cengar saws, these can sha er causing injury to yourself and others. NEVER operate saw without wearing safety glasses NEVER operate saw whilst you, or others are near the saw blade, which can cause serious injury or trapping NEVER use excessive force, this may increase vibra on above safe levels NEVER hold the Cengar saw in a vice by the body, this will distort the bores, rendering the tool inopera ve. NEVER screw nameplates to the body, as the screws may penetrate an airway or bore. NEVER operate the Cengar saw without lubrica on. NEVER be tempted to clean internal parts with anything other than a clean lint free cloth, and M.S. Cleaner, or Cengar Green oil. NEVER modify Cengar saws or use non Cengar parts, this will invalidate ATEX approval, and warranty. ALWAYS ALWAYS use Cengar green oil for best results. Keeping the saw clean and well oiled will give excellent reliability, and a long life. ALWAYS use Cengar Bi‐Metal Sha erproof blades, for safety, and best cu ng performance ALWAYS isolate the air supply when changing blades. ALWAYS wear eye protec on when using sawing machines. ALWAYS keep the nosepiece abu ed to the work to prevent excessive vibra on ALWAYS isolate the machine when not in use...
450 mm long x 25 mm blade, pitches 6, 8, 10, & 14 Other types available on request Cengar Green Oil GO 9107P Cengar Green Oil 250 ml plas c bo les for all air tools GO 9109 As above in 5 litre container GO 9110 As above in 25 litre container M.S. Cleaner MS 9105 1 litre General purpose cleaning fluid for air tools. MS 9125 50 ml. In a dropper bo le. ‐ Enough for 10 tools Always use plenty of Cengar green oil a erwards. ...
Page 12
SERVICE We offer a full factory repair and refurbishment service for Cengar Saws, ‐ normally within 5 working days. Quota ons at no charge can be given before work is carried out. DISTRIBUTOR ADDRESS Cengar. Ltd. Springfield Works, Saddleworth Road Halifax, England HX4 8LZ Tel: 01422 377904 Fax: 01422 377161 enquiries@cengar.com www.cengar.com Original Instruc ons Document No. MANJSZENG/01 Issue 07 (Dec ‘13) ...