LG 55LH80YD-AB Service Manual page 14

* Adjustment environment and reference
1) Environment illuminance
Adjust it to 10 LUX or less at the place where the light
source such as lamp should be blocked at maximum.
2) Probe location
: Maintain the Color Analyzer (CA-210) close to the
module surface by 10cm or less and keep the probe of
the Color Analyzer perpendicular to the module
surface (80°~ 100°).
3) Aging time
- Keep the power on after the aging start (with no power
off) to perform the heat run for 15 minutes or longer.
- Make sure that the back light is turned on by using no
signal and the full white pattern or others.
• Standard color coordinate and temperature using CS-1000
Mode Color Coordination
x
COOL 0.276
MEDIUM 0.285
WARM 0.313
• Standard color coordinate and temperature using CA-210(CH 10)
Mode Color Coordination
x
COOL 0.276±0.002
MEDIUM 0.285±0.002
WARM 0.313+0.002
5.3 Option selection per country
(1) Overview
- Option selection is only done for models in Non-USA
North America due to rating
- Applied model: LA92A Chassis applied None USA
model(CANADA, MEXICO)
(2) Method
1) Press ADJ key on the Adj. R/C, then select Country
Group Menu
2) Depending on destination, select KR or US, then on the
lower Country option, select US, CA, MX. Selection is
done using +, - KEY
• TV
- Adjust directly if it's not a Wireless/Wired state
- Adjust after changing to HDMI5 on the Wireless/Wired state
• Media-Box
- Adjust on the Wireless/Wired state that is excepted the
HDMI5.
Copyright © 2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
Temp
y
0.283 11000K
0.293 9300K
0.329 6500K
Temp
y
0.283±0.002 11000K
0.293±0.002 9300K
0.329±0.002 6500K
5.4 EYE-Q Function Check
Step 1) Turn on TV
Step 2) Press EYE key of Adj. R/C
Step 3) Cover the Eye Q II sensor on the front of the using
Step 4) Confirm that R/G/B value is lower than 10 of the
Step 5) Remove your hand from the Eye Q II sensor and wait
Step 6) Confirm that "B. Light(xxx)" value increases from 0.
∆UV
0.0000
0.0000
< step 2>
0.0000
∆UV
0.0000
< step 5>
0.0000
5.5 Wireless Pairing
0.0000
(1) Overview
To set 1:1 connection from selecting the same Wireless
channel on the TV and Media-Box, and fixing Mac address.
* Set this on the Wired (HDMI cable connection) state.
(2) Method
1) Press ADJ Key on the adjustment R/C and select "9.
Wirelesss Pairing" and access to the Manu with using the
ENTER key.
2) Make to display "OK" on paired stauts of items by using F/
G , after select LRP Channel
3) Media-box turn off/on and then confirm connection of
Wireless, after remove HDMI cable
- 14 -
your hand and wait for 6 seconds
"Raw Data (R: G: B: )" .
If after 6 seconds, R/G/B value is not lower than 10,
replace Eye Q II sensor
for 6 seconds
If change is not seen, replace Eye Q II sensor
< step 3>
Green Eye-Check
Sensor Data: 215
Backli ght : 100
< step 6>
Green Eye-Check
Sensor Data: 1
Backlight: 0
O.K
< step 4>
LGE Internal Use Only