Lux Products TradePro TP-LH121 Installation And Operating Instructions

INSTALLATION AND OPERATING
INSTRUCTIONS
TP-LH121
DIGITAL ELECTRONIC HEAT PUMP THERMOSTAT
WARNING: Use Energizer
Batteries Only.
Energizer is a registered trademark of Eveready
®
Battery Company, Inc. DURACELL
The Gillette Company, Inc.
I M P O R T A N T !
Please read all instructions carefully before beginning
installation and save for future reference. Before
removing any wiring from your existing thermostat, its
wires must be labeled with their terminal designations.
Ignore the color of the wires since they may not
comply with any standard.
Thank you for your confidence in our product. To obtain the best results
from your investment, please read this manual and acquaint yourself with
your purchase before installing your new thermostat. Then follow the
installation procedures, one step at a time. This will save you time and
minimize the chance of damaging the thermostat and the systems it
controls. These instructions may contain information beyond that required
for your particular installation. Please save for future reference.
COMPATIBILITY
TP-LH121 is designed
for use with single stage
heat pump systems with
auxiliary and/or emergency
heat. These systems are
typical known as 2-stage
heat one stage cool heat
pump systems.
FEATURES
Vertical or Horizontal Orientation
●
Large easy to read backlit display
●
Mode and Fan control for ease of use
●
Simple Temperature UP and Down
●
Control.
Calibration control
●
Temperature Swing adjustability (9
●
levels)
2 or 5 minute compressor delay
●
Fahrenheit or Celsius selection
●
Temperature Limits for High and Low
●
selections
Test mode to temporarily disable the
●
compressor delay
or DURACELL Alkaline
® ®
is a registered trademark of
®
TEMP UP
TEMP DOWN
Patent # 6,951,306
© COPYRIGHT 2016 LUX PRODUCTS CORPORATION. ALL RIGHTS RESERVED
OPERATING INSTRUCTIONS
In the winter, set the system switch to HEAT to control your heating
●
system.
In the summer, set the switch to COOL to control your air conditioner.
●
● Press either the TEMPERATURE UP or DOWN key in order to show
the current SET TEMPERATURE.
●
Press TEMPERATURE UP or DOWN keys again until your desired
temperature is displayed. The display will show the current room
temperature again after two seconds.
●
Press the light bulb button to illuminate the display. Adjusting the
temperature will keep the display lit until no button has been pressed
for over ten seconds.
In spring and fall or when windows are open, you can set the system
●
switch to OFF.
Setting the FAN switch to AUTO automatically runs your system's fan
●
during heating and cooling.
Setting the FAN switch to ON runs your system's fan continuously even
●
without heating or cooling.
Setting the Mode switch to EMER (emergency heat) runs your
●
Emergency heating system rather than the heat pump.
INSTALLATION
Please read all instructions carefully before beginning installation.
Turn off electricity to the appliance before installing or
servicing thermostat or any part of the system. Do not turn
OFF
electricity back on until work is completed.
Do not short (jumper) across electric terminals at control on furnace or
●
air conditioner to test the system. This will damage the thermostat and
void your warranty.
All wiring must conform to local codes and ordinances.
●
This thermostat is designed for use with 24 volt and millivolt systems.
●
The thermostat should be limited to a maximum of 1.5 amps; higher
current may cause damage to the thermostat. If you are in doubt, call
your HVAC contractor.
MODE
Your thermostat is a precision instrument. Please handle it with care.
●
TOOLS REQUIRED
#1 Phillips screwdriver (small)
●
Wire Stripper
●
FAN
Drill
●
MODE
THERMOSTAT LOCATION
On replacement installations, mount the new thermostat in place of the
old one unless the conditions listed below suggest otherwise. On new
installations, follow the guidelines listed below.
Remember that your TP-LH121 may be mounted vertically or
●
horizontally when determining the optimal location.
Locate the thermostat on an inside wall, about 5 ft. (1.5m) above the
●
floor, and in a room that is used often.
Do not install it where there are unusual heating conditions, such as: in
●
direct sunlight; near a lamp, radio, television, radiator, register, or
fireplace; near hot water pipes in a wall; near a stove on the other side
of a wall.
Do not locate in unusual cooling conditions, such as: on a wall
●
Do not locate in a damp area. This can lead to corrosion that will
●
shorten thermostat life.
Do not locate where air circulation is poor, such as: in a corner or an
●
alcove; or behind an open door.
Do not install the unit until all construction work and painting has been
●
completed.
C A U T I O N