Table of Contents
Advertisement
Quick Links
1310nm Optical Transmitter
1. Features
Switchable AGC and MGC function, support remote control by webmaster
LCD real-time displays working parameters
Sound-light alarm
Two options for national standard webmaster transponder
2. Diagram
Input TEST
RF Input
Frequence
Signal Mixed
Response ADJ
3. Surface Structure
Mixed
Electric
Frequence
ATT
Response ADJ
AGC
NEII
Incentive TEST
Pre
Distortion
RF Power
RF
Incentive power
Detect
Cut-off
detection
MPU
LCD
User's manual
Optical
Out
DFB
Laser
Laser
APC
ATC
parameter
Key
Unit
Advertisement
Table of Contents
Summary of Contents for C-Data HF200-3613 series
- Page 1 User’s manual 1310nm Optical Transmitter 1. Features Switchable AGC and MGC function, support remote control by webmaster LCD real-time displays working parameters Sound-light alarm Two options for national standard webmaster transponder 2. Diagram Input TEST Incentive TEST Optical Mixed Electric...
-
Page 2: Basic Parameter
User’s manual Item Specification ON: Turn on OFF: Turn off Key Switch Red light: Wrong parameters Alarm Light Green light: Correct parameters Display working status and parameters of device Display Screen Menu page turning, reducing attenuation value LEFT Button ESC Button Exit menu item SET Button Set menu item... -
Page 3: Link Performance
User’s manual Estimated Link Loss: Power(mW) Estimated Link Loss (dB) Power(mW) Estimated Link Loss (dB) 12.5 12.8 10.0 13.0 10.0 13.3 11.0 13.6 11.4 13.8 11.7 14.0 12.1 Remark1: Estimated Link Loss is the sum of 10km fiber loss and passive loss 4.2 RF Parameter RF Band 47～1000 MHz... -
Page 4: General Parameter
User’s manual Rmark: C/N、C/CTB and C/CSO are tested with meeting estimated link condition C/N is tested with PAL-D loading 59 TV channels in 550MHz C/CTB and C/CSO is the typical value when 59 TV channels are configured in 550MHz, regardless of receiver distortion 4.4 General Parameter Power Supply AC: 100～240V... -
Page 5: Operation Overview
User’s manual 5. Operation Overview HF200-3613 series indoor 1550 optical transmitter of Network Technology LTD. Panel operating and displaying function are added based on former similar optical transmitter, user can view almost all working parameters of device locally through LCD, these operations are all based on multi-level function menu, simple and clear HMI achieved “simpleton operation.”... - Page 6 User’s manual 5.2 National Standard Class 2 Transponder HF200-3613 series indoor 1310 optical transmitter can optionally configure with national standard class 2 transponder (refers to NE2 in the following). With webmaster that meets national standard, remote control for devices can be achieved.
-
Page 7: Keyboard Operation
User’s manual multiple same model receivers, receivers will be recognized by their MAC address as each device has different MAC address, which can be checked on LCD. 6. Keyboard Operation Keyboard has 4 buttons including “SET”, “ESC”, “LEFT” and “RIGHT” 6.1 SET Enter key, mainly has following functions: ... - Page 8 User’s manual Device model Device serial number Software version MAC address (show console login/password when NE2 is configured 7.3 Working Parameters Show optical transmitter working parameter list, and mark normal or not (“normal”, “too high”, “too low”). Including: ...
-
Page 9: Network Management
MAC address as each device has different MAC address, which can be checked on LCD. 8.2 National Standard Class 2 Transponder Mode HF200-3613 series indoor 1310 optical transmitter can configure with NE2 optionally, with webmaster that meets national standard, remote control for optical transmitters can be achieved. - Page 10 User’s manual with the device, but it can not be the same IP address, then use UTP to connect device through Telnet. Username: sysadmin Password: admin Attention: There is case sensitive After logging in the device, use command “ip” to set new IP address, like: ip 192.168.1.211 It means changing the device IP to 192,168.1.211 Command “ip”...
-
Page 11: Installation
User’s manual 3）Open device PC hyper terminal will show the prompt requiring username, if it does not show up please press “Enter” in the keyboard 4）Log in device, change IP address The same operation as Telnet method Log-in account/password of console port can be checked by command “... - Page 12 User’s manual ③ RF input signal requirements: Nominal RF input signal of this transmitter is 75(+3/-3)dBuv for each channel with loading 59 channels. To achieve ideal transmission characteristics, transmitting signal level difference among channels should be within ±0.5dB It is particularly stressed that RF input level in each channel can not be more than 82dBuv, or the laser might be damaged ...
-
Page 13: Notes For Using
User’s manual Starting-up and Debugging After finishing all above preparation works, electrical test can be processed. Turn on the power switch on back panel, indicator shows red light, screen lights up, it means the whole device is powered up normally. Then turn on the key switch on front panel and adjust the button on it, select necessary working status. - Page 14 User’s manual optical transmitting link, this device applies good quality FC/SC connector, it must apply good quality active fiber connector in the same specification to ensure system working stably and reliably. Cleanness of All active connectors need to be ensured as well. It is required to clean active connectors by compressed air or specialized alcohol for each reconnection.