Ozone Solutions OMZ-1000-HF Operation And Maintenance Instructions

2. After shipping the unit via courier or after rough handling such as falling off a shelf open cabinet by following
step 1 of the cleaning instructions. Check to make sure the center screen of the generator plate has not moved
out of place. Once this has been checked the plate rack may be reinstalled and the unit is ready for use.
CAUTION, THIS OZONE GENERATOR OPERATES AT 4000-5000 VOLTS AC
SPECIFICATIONS FOR OMZ-1000-HF (HFT) Ozone Generator
Maximum output
Fan (rated cfm)
Filter
Cabinet material
Generation method
Weight and size
INTRODUCTION
This line of ozone generators are designed for various uses at varying output levels. This ozone generator can be
used for many uses such as deodorizing cars homes as well as oxidizing many organic contaminants.
WARRANTY
The OMZ-1000HF(HFT) is warranted against defects in materials and workmanship for a period of four years from
date of purchase. Liability is limited to parts and labor only. Shipping is the sole responsibility the customer. OZSL is
not liable for damage caused by shipping, misuse, neglect or lack of regular maintenance.
LIABILITY
OZSL assumes no responsibility for any damage done to items from the use or miss use of any product sold or
manufactured by OZSL. It is the customers responsibility to test materials prior to use and to ensure that the
procedure and installation technique they are using is correct for the application.
HEALTH AND SAFETY
Ozone can be an irritant and a powerful oxidizing agent. As with most all products, ozone is dangerous only when
used improperly, as such it is important to follow safe usage guide lines.
*When doing a shock treatment, no people plants or pets/animals may be in the room when the unit is running.*
The room should not be reentered until all ozone has been depleted unless proper breathing respirators are used.
MAINTENANCE FREQUENCY
Under heavy duty use or severely polluted areas, The ozone generator should be inspected and cleaned if
necessary every 2 to 3 weeks for fine dust or oily residue collecting on generator surfaces or plates. Light duty
use requires cleaning every 2 to 6 months depending on the severity of pollution and the humidity level of the
feed air. In dirty and humid conditions cleaning can be as often as 2-4 weeks.
DESCRIPTION OF OZONE GENERATOR
These ozone generators produce ozone by corona discharge, converting normal oxygen to ozone gas which is a
very strong oxidizing agent used to destroy odors and other organic contaminants. This model comes from the
factory with 1 plate, producing up to 1000mg/hr, and can be upgraded by adding as many as 4 additional plates to a
max of 3,600mg/hr.
PLACEMENT OF UNIT
This ozone generator is designed as a portable commercial deodorizing device. It uses 120VAC for North America,
and 220-240VAC for European countries etc. European models come with an IEC connector and it is up to the
customer to supply the proper cord (this can be acquired at any computer shop).
Please note the following points when placing the unit.
-Place on a flat solid surface such as a table or shelf. Do not place on rug flooring to reduce dust entering the unit
-Do not place in an area where the unit could be splashed with water, moisture or in an area that it could get
flooded with water.
-Ensure that the unit gets proper fresh air flow. Do not obstruct the incoming or outgoing air from the unit.
-DO NOT USE IN VICINITY OF COMBUSTIBLE GASSES!!
-Humidity levels higher than 75% should be avoided as it will cause the unit to wear excessively fast and will
require cleaning much more often.
-If used in temperatures below freezing, ensure that condensation inside the unit does not occur.
-Set the unit in an area where it will provide the best ozone distribution.
-The use of circulation fan will greatly increase the efficiency of the treatment.
-If the ozone generator being used is large enough to treat the whole house, the air handling system can be used
to distribute the ozone, just point the ozone generator into the return air duct.
OMZ-1000-HF (HFT)
Operation and Maintenance Instructions
1. Read instructions thoroughly before operating!!
DISCONNECT POWER BEFORE OPENING TO SERVICE
1,000 mg/hr (1 ozone plate) / upgradable to 3,600 mg/hr (5 ozone plates)
105 cfm
1 Cleanable foam filter
PVC outer cabinet with stainless steel inner chassis
Corona discharge
10.5-lb 21" long x 5" wide x 6-5/8" height (including handle)
IMPORTANT!!!!!