Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for VISIO BW-1210 QW
Summary of Contents for VISIO BW-1210 QW
-
Page 1: User Manual
BW-1210 QW User Manual Please read the instructions carefully before use... -
Page 2: Table Of Contents
CONTENTS 1. Safety Instruction ..........................2 2.Techical Specfications ........................4 3. How To Set The Fixture........................5 3.1 Control Panel ........................5 3.2 Main Functions ........................6 4. How To Control The Unit......................12 4.1 Master/Slave Built In Preprogrammed Function ............12 4.2 DMX Controller ........................12 4.3 DMX 512 Configuration.....................14 5. -
Page 3: Safety Instruction
1. Safety Instruction Please read the instructions carefully which includes important information about the installation, operation and maintenance. WARNING Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. Caution: All fixtures are intact from the manufacturer, please operate follow up the user manual, artificial fault are not under guarantee repair. - Page 4 DO NOT touch any wire during operation as there might be a hazard of electric shock. Avoid power wires together arounding other cables. Replace fuse only with the same type. In the event of serious operating problem, stop using the unit immediately. Never turn on and off the unit time after time.
-
Page 5: Techical Specfications
2.Techical Specfications Features: ◆ - An ideal replacement for the outdoor metal halide fixtures - VPad Smart and VPad White produces powerful and consistent light output, makes its efficiency and cost-effective - Compact design with great heat ventilation in a rugged die-cast aluminum housing to ensure reliable performance under harsh environment - 16 pre-programmed movement patterns and 4/5/7 DMX channels - Easy installation with swivel tilt mechanism for quick positioning. -
Page 6: How To Set The Fixture
3. How To Set The Fixture 3.1 Control Panel 1. Display: To show the various menus and the selected functions Button: 2. MENU To select the programming functions To confirm the selected functions 3. ENTER 4. DOWN To go backward in the selected functions 5. -
Page 7: Main Functions
3.2 Main Functions To select any functions, press the MENU button until the required one is showing on the display. Select the function by the ENTER button and the display will blink. Use the DOWN and UP button to change the mode. Once the required mode has been selected, press the ENTER button to setup or it will automatically return to the main functions without any change after idling one minute. - Page 9 DMX 512 Address Setting Select the , press the ENTER button and the display will blink. Use the DOWN and UP button to adjust the DMX512 address between . Once the address has been selected, press the ENTER button to setup or automatically exit menu mode without any change after one minute.
- Page 10 ENTER button to setup or automatically exit menu mode without any change after one minute. To go back to the functions without any change press the MENU button. Manual Mode Select the , press the ENTER button and the display will blink. Use the DOWN and UP button to select the (Red), (Green),...
- Page 11 UP button to adjust the intensity value between . Once selected, press the ENTER button to setup or automatically return to the main functions without any change after one minute. Back to the previous functions press the MENU button. Time Setup Press the MENU button to show on the display.
- Page 12 button and the display will blink. Use the DOWN and UP button to select the (normal) (inverse)，Once the mode has been selected, press the ENTER button to setup or automatically return to the main functions without any change after one minute. To go back to the previous functions without any change press the MENU button.
-
Page 13: How To Control The Unit
Software version Press the MENU button up to when the is blinking on the display. Press the ENTER button and the display will show the version of software of the unit. To go back to the functions press the MENU button again. 4. - Page 14 Please refer to the following diagram to address your DMX512 channel for the first 4 units：...
-
Page 15: Dmx 512 Configuration
4.3 DMX 512 Configuration 4/5/7 Channels Mode:... -
Page 16: Dmx512 Connections
5. DMX512 Connections 1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin adapter-cable. 2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in the DMX-output of the last unit. -
Page 17: Troubleshooting
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+), Pin 4/Pin 5: Not used. 6. Troubleshooting Following are a few common problems that may occur during operation. Here are some suggestions for easy troubleshooting: Problem Possible Cause Action... -
Page 18: Fixture Cleaning
7. Fixture Cleaning The cleaning of internal must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the fixture’s optics. Clean with soft cloth using normal glass cleaning fluid. -
Page 19: Declaration Of Conformity
Declaration of Conformity We declare that our products (lighting equipments) comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility (EMC) Directive 89/336/EEC. EN55103-1: 2009 ; EN55103-2: 2009; EN62471: 2008; EN61000-3-2: 2006 + A1:2009 + A2:2009; EN61000-3-3: 2008. &...
Need help?
Do you have a question about the BW-1210 QW and is the answer not in the manual?
Questions and answers