Advertisement
Quick Links
Certification Exhibit
FCC ID: ONTJETIR5US
IC: 10491A-JETIR5US
FCC Rule Part: 15.247
IC Radio Standards Specification: RSS-210
ACS Project: 13-2001
Manufacturer: Esprit Model
Models: JETIR5LUS, JETIR5iUS, JETIR4LUS, JETIR4iUS
User Manual
3998 FAU Blvd. Suite 310 Boca Raton, FL 33431 Tel: 561-961-5585 Fax: 561-961-5587
Advertisement
Related Manuals for JETI model JETIR5iUS
Summary of Contents for JETI model JETIR5iUS
-
Page 1: User Manual
FCC ID: ONTJETIR5US IC: 10491A-JETIR5US FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Project: 13-2001 Manufacturer: Esprit Model Models: JETIR5LUS, JETIR5iUS, JETIR4LUS, JETIR4iUS User Manual 3998 FAU Blvd. Suite 310 Boca Raton, FL 33431 Tel: 561-961-5585 Fax: 561-961-5587... - Page 2 The JETI DUPLEX EX series of receivers are designated to operate with the JETI DUPLEX EX transmitters using the 2.4GHz band. Thanks to the fully digital and bidirectional communication between the transmitter and receiver the Duplex EX system offers many new features and concepts for the remote control pilot.
-
Page 3: Operation
Operation: Operation of the DUPLEX system is very similar to a traditional FM system. We recommend that you switch on the transmitter first and then the receiver. The transmitter confirms the on state of the receiver sounding a short beep. When switching off the system we recommend that you switch off the receiver first and then the transmitter. - Page 4 one or more of the E4 EX expanders connected to the receiver Ext port. Bidirectional Signal Loss Alert: An alarm will sound if you lose the bidirectional telemetry data communication between your transmitter and receiver. This alarm simply means that at the given instant there is no data available from the telemetry sensors or other equipment connected to the receiver input (Ext.
- Page 5 Overview of Receiver Data Items Once in the Jetibox emulator the Tx screen is displayed, press the right arrow button to go to the Rx info screen. Then press the down arrow button to go the Rx introductory screen. The introductory screen displays the type of receiver.
- Page 6 - Signal Fault Delay: specifies the deadline after which the receiver outputs change due to signal loss to preadjusted positions of the particular outputs or after which they become switched off (due to setup of Signal Fault in the menu Out Pin Set). - Volt act/alarm: the first item shows the actual receiver supply voltage, the second value serves for the setup of the alert decision threshold.
- Page 7 -Signal fault: (valid for RSat and RMK) behaviour setup of the satellite receiver in case of signal loss. - Individual set: the behaviour of the output in case of a signal loss will be conducted by the setup of particulat channels in the menu Measurement/Setup –...
- Page 8 This function is of use in case of a bidirectional connection of several receivers or satellite receivers. The output channel marked Sat 1 can be set to PPM signal mode only. -Set mode SAT: on the Duplex receivers R9,R10, R11EPC, R12EPC, R14, R18 the outputs SAT1 and SAT2 can be affiliated with following functions - PPM Off: the particular output is neither generating nor receiving a...
- Page 9 positions, out off – output switched off, FailSafe – transition to preset throw positions of individual outputs which may be set up in the FailSafe menu. -FailSafe: throw setup of a selected output in case of signal loss -Delay: delay of servo speed (at the output) in case of a change at the input, the entry time corresponds with the transit time within the output range between 1ms to 2ms which, for instance, may be suitable for...
- Page 10 be co-located or operating in conjunction with any other antenna or transmitter.” THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS. (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
- Page 11 : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. We wish you successful flying with the products of: JETI model s.r.o. Příbor, www.jetimodel.com...