Table of Contents
Advertisement
Save This Manual for Future Reference
Original Instruction
L IT T E R
L O G S P
Log Splitter
Operator's Manual
MODEL NUMBER :
SERIAL NUMBER :
Both model number and serial number may be found on the main
label. You should record both of them in a safe place for future use.
FOR YOUR SAFETY
READ AND UNDERSTAND THE ENTIRE MANUAL BEFORE
OPERATING MACHINE
8
Advertisement
Table of Contents
Summary of Contents for Bushranger LS301
- Page 1 Save This Manual for Future Reference Original Instruction L IT T E R L O G S P Log Splitter Operator’s Manual MODEL NUMBER : SERIAL NUMBER : Both model number and serial number may be found on the main label.
-
Page 2: Table Of Contents
TABLE OF CONTENTS INTRODUCTION Introduction Specifications Symbols Safety ite ia it e Contents Supplied e ate an Assembly Know Your Machine Operation Carefully read through this entire Transporting operator's manual before using Maintenance your new unit. Pay attention to all cautions and warnings. -
Page 3: Specifications
Specifications Model # LS301 Splitting Force* 30 ton Log Capacity 655 mm Engine Kohler Command Pro CH395 Displacement 277 cc Gross Torque @ 2600rpm 20 ONM Fuel Capacity Engine Oil Capacity 1.3 L Starting System Recoil Control Valve Auto Return with Adjustable Detent... -
Page 4: Symbols
ENVIRONMENTAL Keep children and bystanders o and away from the log splitter. Recycle unwanted materials instead of disposing of them as waste. All tools, hoses, and packaging should Be sure the engine's switch is be resorted, taken to the local before transporting the recycling center and disposed of in machine or performing any... -
Page 5: Safety
a responsible adult. Do not operate the machine while under the influence of drugs, alcohol, or any medication that could affect your ability to use it properly Do not transport with objects on the machine. Dress properly. Wear heavy long pants, boots, MAX. - Page 6 Regularly check to see that keys and adjusting tank indoors. wrenches are removed from the machine area Keep grounded conductive objects, such as before starting it. A wrench or a key that is left tools, away from exposed, live electrical parts attached to a rotating part of the machine may and connections to avoid sparking or arcing.
- Page 7 in the hydraulic system can penetrate skin Keep the work area free of clutter. Remove and result in serious injury or death. Be sure to split wood from around the log splitter stop the engine and relieve hydraulic pressure immediately after each use to avoid potential before doing any work on hydraulic parts.
- Page 8 Machine use and care Never transport cargo on the log splitter. Never operate the machine without good Never allow anyone to ride or sit on the log visibility or light. splitter. Never attempt to split wood across the grain. Always stop the engine, lock the beam in the The log splitter was not designed for cross- horizontal position, and close the fuel shut-off grain splitting.
-
Page 9: Contents Supplied
CONTENTS SUPPLIED Your log splitter comes partially assembled and contains the following: OPTIONAL 1. Beam with Cylinder 13. Hardware Kit, Including: 2. Reservoir with Engine 3. Beam Lock Bracket 4. Pivot Bracket 5. Log Cradle (Left) 4 X 50 6. Log Cradle (Right) 7. -
Page 10: Assembly
Assistant holds the engine, while the other ASSEMBLY person assembles the wheel opposite of the engine first. This log splitter was partially assembled at the factory. To assemble your machine follow the below instructions. WHEELS Remove the anti-dust sleeves from the two wheels. - Page 11 opposite directions so the axle nut will not A f t e r t h e b e a m a n d c y l i n d e r come off (make sure the tyre spins freely). assembly is in the vertical position, a helper is needed to prevent the beam Installation of the cotter pin is from tipping over until it is secured...
- Page 12 PIVOT BRACKET Align the pivot bracket on the beam assembly to the pivot mount on the tank Align the holes in the pivot bracket with the weldment and insert the beam pivot pin holes on the beam and insert and tighten and washer.
- Page 13 Hold the lifting handle and slowly lower the 2. Follow step 1 to assemble the left log cradle. (See Figure 9) beam. It will lock automatically. Double check to make sure the beam bracket is Inside Holes Outside Holes locked onto the beam. Do not let the beam suddenly drop.
-
Page 14: Know Your Machine
KNOW YOUR MACHINE Features and Controls Log Table (Optional) Log Spinner Foot Plate 2-Position Log Cradle 4-Way Wedge(Optional) Log Stripper Split Control Handle Cylinder Lifting Handle Hydraulic Breather/Dipstick Reservior Manual Tube Beam Lock Bracket Beam Assembly Support Leg 2” Ball Hitch Coupler Safety Chains Hydraulic Pump Control Valve... - Page 15 Engine On/O Switch Recoil Starter Handle Throttle Control Choke Control Fuel Shut-O Valve LOG SPINNER FOOT PLATE LIFTING HANDLE The foot plate holds the log in place while The lifting handle is included for easy the wedge splits the log. transition from horizontal to vertical.
-
Page 16: Operation
RECOIL STARTER HANDLE Using a funnel, add oil up to the FULL mark on the dipstick. (See engine manual for oil The handle is used to start the engine. capacity, oil recommendation, and location FUEL SHUT-OFF VALVE of fill cap.) The fuel shut –... - Page 17 STOP ENGINE STARTING ENGINE Return the cylinder to fully retracted position Make sure the control lever is in the neutral or home position. Move the Throttle lever to position. SLOW ( ). Move the engine switch to OFF. Move the engine Close the fuel shut-off valve ( switch to the ON Sudden stopping at a high speed,...
- Page 18 CONVERSION BETWEEN HORIZONTAL Neutral Position S P L I T T I N G P O S I T I O N A N D V E R T I C A L Forward Reverse SPLITTING POSITION Position Position Horizontal Beam Lock Figure 11a Horizontal Position Lifting Handle...
-
Page 19: Transporting
TRANSPORTING When seating a bead after repair, do not exceed 30 PSI. Pressures MOVING BY HANDS higher than 30 PSI can cause the t re wheel rupture The log splitter is heavy. It can and explode. crush and cause serious injury if it rolls out of control or tips over. -
Page 20: Maintenance
Lock the support leg in the DOWN position and disconnect from vehicle. Never operate the log splitter while it is attached to the vehicle. Oil-drain plug MAINTENANCE Figure 13 Inspect and maintain the log splitter before ADD HYDRAULIC OIL TO OIL TANK each use. -
Page 21: Storage
If fuel is stored must report the fault of defect to an authorised Bushranger dealer and provide proof of purchase o v e r 3 0 d a y s , t h e n d r a i n t h e within the relevant warranty period specified. -
Page 22: Troubleshooting
Scored or bent cylinder rod Contact customer service Loose hydraulic fitting Oil leak from cylinder Tighten hydraulic fitting Faulty combination washer Contact your Bushranger Dealer seal on cylinder hydraulic fitting Oil leak from hose Loose hose clamp or hydraulic Tighten hose clamp or hydraulic fitting connection fitting... - Page 23 ILLUSTRATED PARTS LIST FOR LS301 30T LOG SPLITTER LOG SPLITTER...
-
Page 24: Parts Diagram
PARTS DIAGRAM LOG SPLITTER... -
Page 25: Parts List
PARTS LIST Part Number Description Part Number Description 50001 Pin 35 50040 Spring Washer 8 50002 Bridge Pin 50041 Bolt M8x20 50003 Hose Clamp 40 50042 Washer 8 50004 Hex Socket Head Cap 50043 Bolt M12x90 Screw M6x20 50044 Cotter Pin 4x50 50005 Right-Angle Fitting 50045... -
Page 26: Notes
Part Number Description 50080 Suction Hose 50081 Return Oil Filter 50082 O-Ring D81*3.1 50083 Flange of Filter 50084 Washer 6 50085 Bolt M6x16 50086 Safety Chain 50087 Bolt M12x80 50088 50mm Ball Hitch 50089 Pipe Plug 48 50090 Safety Clasp 50091 Latch Rod 50092... - Page 27 NOTES LOG SPLITTER...
- Page 28 1300 363 027 for more information. Bushranger™ is a trademark of Roy Gripske & Sons Pty Ltd. PLP shall not be liable for technical or editorial errors or omissions contained herein, nor for incidental or consequential damages resulting from furnishing this material.