Advertisement
THROTTLE POSITION SENSOR
Removal & Installation (Except 1.3L & 1.8L)
1) Turn ignition off. Disconnect harness connector from
Throttle Position (TP) sensor. Remove TP sensor retaining screws.
Remove TP sensor from throttle body.
2) With throttle valve in closed position, install TP sensor
on throttle body. Ensure TP sensor lever engages with drive lever on
throttle shaft. Install retaining screws and harness connector. TP
sensor is self-zeroing and is not adjustable.
Removal & Installation (1.3L & 1.8L)
1) Disconnect negative battery cable. Disconnect harness
connector from TP sensor. Remove TP sensor retaining screws. Remove TP
sensor from throttle body.
2) To install, mount TP sensor on throttle body with
alignment slots slightly counterclockwise of body holes. Turn TP
sensor clockwise to align holes and install retaining screws finger
tight. To complete installation, reverse removal procedure. Adjust TP
sensor. See appropriate ON-VEHICLE ADJUSTMENTS article. Tighten TP
sensor retaining screws to specification. See TORQUE SPECIFICATIONS.
EMISSION SYSTEMS & SUB-SYSTEMS
CHARCOAL CANISTER
Removal & Installation (1.3L, 1.9L, 2.2L, 2.4L, 3.0L, 3.5L,
4.0L & 4.6L)
Raise and support vehicle. Disconnect hoses from charcoal
canister filter. Remove charcoal canister filter attaching bolts.
Remove charcoal canister filter. To install, reverse removal
procedure. Tighten bolts to specification. See TORQUE SPECIFICATIONS.
Removal & Installation (1.8L)
Raise and support vehicle. Remove muffler. Disconnect fill
limiter vent valve hose from charcoal canister port by pinching both
sides of hose connector. Disconnect hoses from charcoal canister
filter. Disconnect electrical connector from charcoal canister filter.
Remove charcoal canister filter attaching bolts. Remove charcoal
canister filter. To install, reverse removal procedure. Tighten bolts
to specification. See TORQUE SPECIFICATIONS.
Removal & Installation (3.1L, 3.4L & 3.8L)
Raise and support vehicle. Remove fuel tank. Disconnect hoses
and vent pipes from charcoal canister filter. Release canister
retaining strap. Remove charcoal canister filter. To install, reverse
removal procedure. Tighten bolts to specification. See
TORQUE SPECIFICATIONS.
Removal & Installation (5.7L)
Remove fuel tank. Disconnect hoses and vent pipes from
charcoal canister filter. It may be necessary to bend bracket in order
to remove the charcoal canister from bracket. To install, reverse
removal procedure. Tighten bolts to specification. See
TORQUE SPECIFICATIONS.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS
¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡
Advertisement
