Page 1
DMX WIFI Touch Panel Controller Controller Power Cable with Power Cable with converter converter DMX Output Pigtail DMX Output Pigtail Micro USB Cable Mini USB Cable Terminator Kit Terminator Kit Infared Remote OceanLED INSTALL / DMX Controller / 073114 / v4.2...
Page 2
GENERAL OceanLED underwater lights are generally used for illuminating the water around a boat or yacht. Placement for achieving the best results are described in selecting the right location. OceanLED INSTALL / DMX Controller / 073114 / v4.2...
Some OceanLED lights contain combinations of plastic and polymer products which are impervious to salt water corrosion, however, screws and fasteners used for the installation must be of a marine grade type stainless steel or equivalent and monitored annually to ensure the lights remain in service for years to come.
1.1 Tools and Materials WARNING: NEVER USE POWER TOOLS; HAND TIGHTEN ONLY! WARNING: OCEANLED RECOMMENDS DRY FITTING ALL PRODUCTS. WHEN INSTALLING, BESURE THAT THE CONTROLLER FITS THE AREA AND SECURES TO THE MOUNTING LOCATION USING THE APPROPRIATE HARDWARE BEFORE INSTALLING.
Page 5
When switching system on for the first time, take into consideration water clarity, ambient light etc as first time impressions can be marred by poor conditions. • Test units after installation. OceanLED INSTALL / DMX Controller / 073114 / v4.2...
Mount the back plate of the interface on the preferred mounting location. (in a dry place) 86mm X 86mm X 10mm plate. Close the unit by clipping the front panel onto the back OceanLED INSTALL / DMX Controller / 073114 / v4.2...
Page 7
2.3 Specifications DMX Touch Panel Controller Factory Default Programming for DMX Touch Panel Controller (001-500596) Scene Function Green Blue Super White Colour Cycle Compatible with any DMX fixture or DMX LED driver Ready to use (pre-loaded with 8 scenes & 42 RGB fixtures)
Mount the back plate of the interface on the preferred mounting location. (in a dry place) 168 x 128 x 11.5mm. Close the unit by clipping the plate. front panel onto the back OceanLED INSTALL / DMX Controller / 073114 / v4.2...
Page 9
4 on a remote control, hold down the "Select" button and the color fader. Wait for scene 4 to light up, then press button 4 on the remote control. OceanLED INSTALL / DMX Controller / 073114 / v4.2...
Page 10
Red, Green, Blue, White increment Blue / White rapid switch Yellow / Cyan / Blue Switch Cycle / Strobe Modes White Pulse Red / Blue Pulse, White Fade Rapid Green / White Strobe Green Pulse OceanLED INSTALL / DMX Controller / 073114 / v4.2...
Page 11
ESA + ESA PRO on PC/Windows, ESA2 on PC + MAC ARCOLIS + STICK REMOTE on iPhone/iPad/Android Environment IP20, Temp -10˚C to 50˚C Certifications EC, EMC, ROHS, ETL, UL (some in progress) OceanLED INSTALL / DMX Controller / 073114 / v4.2...
4.1 - Finalise your OceanLED Installation WARNING: Always test the lights BEFORE the boat goes back into the water. Typical OceanLED light installs require the boat to be hauled out of the water to replace light units. For the wifi compatible...
Brightness / Speed / and colour of the selected scene can be changed via the select button in the bottom right. For pre-programmed scenes refer to page 10 Scene Selection Select Button 13 13 OceanLED INSTALL / DMX Controller / 073114 / v4.2...
Page 14
Check connected network wifi is Wifi not Resolve issue with network wifi model) functioning correctly functioning Wifi network OK Contact Warranty Department OceanLED INSTALL / DMX Controller / 073114 / v4.2...
This warranty statement is for those products supplied to and sold from all territories internationally OceanLED stands by its products. In general terms, the company gives a full 2 year’s manufacturer’s warranty on all of its products from date of sale.
Contracts (Rights of Third Parties) Act 1999 by any person that is not a party to it. 4: APPLICABLE LAW Each of (a) the sale of the Goods to the Buyer, (b) these conditions, and (c) any disputes or claims arising there OceanLED INSTALL / DMX Controller / 073114 / v4.2...
6.3.5 When you have made contact with the dealer please follow their instructions. 6.3.6 If you are unable to contact a dealer you may wish to contact OceanLED directly. To contact the Service Manager either call our UK office on +44 1455637505 or email sales@oceanled.com.
Page 18
6.4.7 If we are unable to find a problem with the part, we will inform you of the outcome. We can provide guidance to possible reasons for the fault. Unfortunately we are not liable for or can fix problems with equipment & installations that are not purchased from OceanLED. The returned product can be returned to you at your request.