Page 1
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 1 IMPORTANT: IMPORTANT : IMPORTANTE: Read Before Using Lire avant usage Leer antes de usar Operating/Safety Instructions Consignes d’utilisation/de sécurité Instrucciones de funcionamiento y seguridad SPT70V Call Toll Free for Pour obtenir des informations...
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 2 General Power Tool Safety Warnings Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may WARNING result in electric shock, fire and/or serious injury.
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 3 repaired before use. Many accidents are correct power tool will do the job better and safer at the rate for which it was designed. caused by poorly maintained power tools. Do not use the power tool if the switch does Keep cutting tools sharp and clean.
Page 4
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 4 last the life of the saw. If the switch should center the saw blade in the kerf and so that fail in the “OFF” position, the saw may not the saw teeth are not engaged into the start.
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 5 The lower guard may be retracted manually backwards over your hand. only for special cuts such as “plunge cuts” Do not use the saw with an excessive and “compound cuts”. Raise the lower depth of cut setting.
Page 6
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 6 Symbols IMPORTANT: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.
Page 7
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 7 Symbols (continued) IMPORTANT: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 8 Functional Description and Specifications Disconnect the plug from the power source before making any assembly, adjustments or changing accessories. Such preventive safety WARNING measures reduce the risk of starting the tool accidentally.
Page 9
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 9 Functional Description and Specifications Disconnect the plug from the power source before making any assembly, adjustments or changing accessories. Such preventive safety WARNING measures reduce the risk of starting the tool accidentally.
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 10 Assembly ATTACHING THE BLADE mount it against the INNER WASHER on Disconnect the plug from the shaft. Be sure the large diameter of the the power source before INNER and OUTER washers lay flush against...
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 11 Inner washer has two sides (Fig. 4). Washer on one side has arbor size marked FIG. 4 1" (25.4 mm). Other side of the washer has arbor size marked as 25.0 mm. Check the hole size of the blade and use the proper size of the washer.
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 12 90° CUTTING ANGLE CHECK Disconnect plug from power source. Set foot to maximum depth of cut setting. Loosen the front and back adjustments screws. Loosen the front and the back bevel adjustment lever. Place the carpenter's square between the blade and the foot.
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 13 WRENCH USAGE Wrench provided has several functions FIG. 10 o t h e r t h a n l o o s e n i n g / t i g h t e n i n g t h e blade bolt (Fig.
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 14 SWITCH Maintain a firm grip and operate the switch When starting the tool, with a decisive action. Never force the saw. hold it with both hands. Use light and continuous pressure.
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 15 CUTTING LARGE SHEETS Large sheets and long boards sag or bend, depending on support. If you attempt to cut FIG. 13 without leveling and properly supporting the piece, the blade will tend to bind, causing KICK- BACK and extra load on the motor (Fig.
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 16 Maintenance To avoid accidents always dis connect the tool from the power supply before cleaning or performing any main tenance. WARNING Service CARBON BRUSHES The brushes and commutator in your tool have...
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 17 CARE OF BLADES When cleaning gum and wood pitch from Blades become dull even from cutting regular blade, unplug the saw and remove the blade. lumber. If you find yourself forcing the saw...
2017-1016_SPT70V_16 inch SKILSAW Worm Drive_manual_SPT70V 2017/10/16 17:30 页 18 Trouble Shooting Read instruction manual first! Remove plug from the power source before making adjustments or assembling the blade. WARNING TROUBLE: SAW WILL NOT START PROBLEM 1. Power cord is not plugged in.
Page 19
SPT are covered by our 180-Day STAY TRUE® Guarantee. The original purchaser may return any eligible SKILSAW professional portable and benchtop power tool for any reason to the original place of purchase, within 180 days from the date of purchase for a full refund.
Need help?
Do you have a question about the SPT70V and is the answer not in the manual?
Questions and answers