PRESIDIUM Multi-Tester III User Handbook Manual
  1. Manuals
  2. Brands
  3. PRESIDIUM Manuals
  4. Measuring Instruments
  5. Multi-Tester III
  6. User handbook manual

PRESIDIUM Multi-Tester III User Handbook Manual

Hide thumbs

Advertisement

Table of Contents

1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Multi-Tester III and is the answer not in the manual?

Questions and answers

Related Manuals for PRESIDIUM Multi-Tester III

Summary of Contents for PRESIDIUM Multi-Tester III

  • Page 2 Presidium Multi-Tester III (PMuT III) User Handbook (English)
  • Page 3 (English Version) I. Disclaimers, Exclusions and Limitations of Liability pg. 03 II. About this book pg. 04 III. About your Presidium Multi-Tester III pg. 05 IV. IMPORTANT NOTICE pg. 07 1. GETTING STARTED with your Presidium Multi-Tester III pg. 08 2.

  • Page 4: Of Liability

    PLEASE READ AND NOTE PRESIDIUM WARRANTY TERMS AND CONDITIONS as stated in the warranty card. Presidium warranty for its testers are subject to proper use by its users in accordance with all the terms and conditions as stated in the relevant user handbook and shall cover only manufacturing defects.

  • Page 5: Ii. About This Book

    II. About this book Thank you for purchasing the Presidium Multi-Tester III (“PMuTIII” or “tester”). This handbook is designed to help you set up your tester and describes all you need to know about how to use your tester accurately and take care of it in line with its requirements.

  • Page 6: Iii. About Your Presidium Multi-Tester Iii

    III. About your Presidium Multi Tester III The Presidium Multi Tester III has been developed to help distinguish between colorless diamonds and moissanite using the combined principles of thermal and electrical conductivity. The measuring probe with electronic circuitry is designed to detect and segregate data collected from the gemstones via a customized micro-controller.
  • Page 7 Included in your package: • Presidium Multi Tester III • Metal stone rest • User handbook • Warranty card • Protective carrying case Retractable Probe Tip Power Indicator LED Display Panel Battery Compartment Adaptor Inlet ON/OFF Switch Ergonomic Grip Probe Protective Cap...

  • Page 8: Iv. Important Notice

    • Do not paint the tester. Paint can clog the moving parts and prevent proper operation. If the tester is not working properly, kindly contact Presidium Customer Service at service@presidium.com. sg or: Presidium Instruments Pte Ltd No. 6 Penjuru Lane...

  • Page 9: Getting Started With Your Presidium Multi-Tester Iii

    1. GETTING STARTED with your Presidium Multi Tester III Powering up your Presidium Multi Tester III This tester can be powered by either the use of an AC adaptor (optional item sold separately) or through the use of batteries. If AC adaptor is used, connect one end of the AC adaptor to the tester (Fig.
  • Page 10 Turning on your Presidium Multi Tester III Remove the protective cover from the probe tip (Fig.1.3). Fig. 1.3 Press the [ON/OFF] button located at the back of the tester (Fig. 1.4). and wait for about 20 seconds to warm up the instrument.

  • Page 11: Battery Information

    Self-calibration should not be attempted. To minimize any risks associated, users should contact Presidium at service@presidium.com.sg or its service center for assistance. In the event that users require the manufacturer...
  • Page 12 To prevent inaccurate readings, replace with new batteries as soon as the low battery indicator lights up or starts to blink. A test should not be performed when the battery power is low or weak. Batteries do not have to be removed when the AC adaptor is in use.

  • Page 13: Performing A Test With Your Presidium Multi-Tester Iii

    2. PERFORMING A TEST with your Presidium Multi Tester III Place the tip of the probe pen against the gemstone and press the test button. Apply sufficient pressure on the tip for correct reading. For mounted jewelry or gemstones: Hold the jewelry or gemstone with one hand and the tester with the other hand (Fig.
  • Page 14 Tests should be conducted on the table of the gemstone. In the event of any doubt, kindly test on the girdle of the gemstones instead. For proper operation of the tester, fingers must be placed on the rubber pads located on both sides of the tester at all times.

  • Page 15: Reading Test Results On Your Presidium Multi-Tester Iii

    Note: For stones with lower thermal inertia, the Presidium Gem Tester / Color Stone Estimator (PGT/ CSE) or the Presidium Duo Tester (PDT) can be used to further differentiate the type of simulants as they detect a wider simulant range.

  • Page 16: Taking Care Of Your Presidium Multi-Tester Iii

    4. TAKING CARE of your Presidium Multi Tester III • The probe and wire tip is extremely sensitive and should be handled with care, especially during the removal of the protective cap from the pen tip. Always replace the protective cap of the pen tip when the probe is not in use.

This manual is also suitable for:

Pmut iii

Table of Contents

Save PDF