Related Manuals for J&R Churrasco
Summary of Contents for J&R Churrasco
- Page 1 CHURRASCO ROTISSERIE OPERATIONS AND SERVICE MANUAL J&R M ANUFACTURING, (972) 285-4855 (Texas) 820 W. Kearney (800) 527-4831 (50 states & Canada) Suite B (972) 289-0801 (Parts and Service) Mesquite, Texas 75149 (972) 288-9488 (Fax)
- Page 2 SN _______________...
-
Page 3: Disposal Of Ashes
WARNINGS! Disposal of Ashes Ashes should be placed in a metal container with a tight-fitting lid. J&R offers ash carts suitable for this purpose. The closed container of ashes should be placed on a noncombustible floor or on the ground, well away from all combustible materials, pending final disposal. - Page 5 CHURRASCO ROTISSERIES (Solid Fuel) OPERATIONS AND SERVICE MANUAL MANUFACTURED BY: J & R MANUFACTURING, INC. 820-B W. Kearney St. Mesquite, Texas 75149 972-285-4855 Rev.09-17...
- Page 7 CONTENTS : 1 – 2 HURRASCO OOKING AGES : 3 – 4 NSTALLATION NSTRUCTIONS AGES PERATION ROUBLESHOOTING REVENTIVE AINTENANCE ARTS HURRASCO RAWING HURRASCO RAWING ARRANTY...
- Page 8 Gaucho. One of the most favorite of all Churrasco meat offerings is Picanha, an outside muscle from the rump roast that is rolled like a cinnamon roll. This is placed onto the spit and then dipped into a plate of coarse salt.
- Page 9 HURRASCO OTISSERIES The very select centers of pork spareribs trimmed down to about 4” in length are threaded onto the sword-spit and cooked quickly in 20 to 30 minutes. The other cut of pork that is popular is the tender eye of the loin. They also usually serve a special Brazilian style pork sausage that actually is rather bland and in fact, reminds me of the Texas German Bratwurst.
-
Page 10: Installation Instructions
INSTALLATION INSTRUCTIONS SHIPPING: The Churrasco Rotisserie will be shipped fully assembled. The spits will be packed inside the cooking compartment. Also, the casters, a grease gun, and a tube of the recommended grease will be in a box inside the unit. - Page 11 VENTING INFORMATION In all cases, it is imperative to obtain the approval of the AHJ (Authority Having Jurisdiction). This will typically be the mechanical inspection department of the local municipality’s building inspection division and/or the local fire marshal. Exhaust hoods should Listed, Type 1 hoods with automatic fire suppression systems and conform to NFPA 96 requirements.
- Page 12 Make sure that the exhaust hood is operating before building a fire. Building a fire in an open pit churrasco rotisserie is practically the same as in a fireplace. We recommend that kindling or safe (low volatility) solid fuel starting blocks be used with small chunks of wood or with charcoal.
-
Page 13: Troubleshooting
TROUBLESHOOTING ROTISSERIE ROTISSERIE NOT TURNING Is the Motor Running? YES – Then check the chain connection between the motor sprocket and t he sprocket on the lowest rotisserie shaft. If the chain is broken, then either repair the chain (usually with a master link) or replace the chain. If the chain is okay, then check the connect ions between the sprocket s and the shaft s . - Page 14 PREVENTIVE MAINTENANCE DAILY: Keep the unit clean. Wipe off after each use and clean thoroughly at the end of the day. Remove all ashes and place in a tightly sealed metal container away from all combustibles. Dispose of ashes only after you are certain that no live coals remain.
- Page 15 J AND R MANUFACTURING, INC. Churrasco Rotisserie Replacement Parts List Item No. Item Description Group 9708 Hi Temp Bushing – For Spit Bolts Bearing 9791 Bronze Bushing – For Spits Shaft Bearing 9718 Shaft Bearing Bearing 9016 Castable Patch (Priced Per Ft.)
- Page 16 J AND R MANUFACTURING, INC. Churrasco Rotisserie Recommended Spare Parts List Item No. Item Description Group 9108 Grease Gun Grease 9161 Super Hi-Temp Grease Grease 9780 30 RPM Rotisserie Gear Motor Motors 9554 Churrasco Spit Rotisserie Accessories 8721 #40 15 Tooth Sprocket 0 Main Shafts Sprockets &...
- Page 19 Revised 04-01-2017 WARRANTY J & R MANUFACTURING, INC. warrants its equipment against defective parts and workmanship under normal use and when installed in accordance with manufacturer’s recommendations for a period (after date of shipment*) of twelve ( 12 ) months on parts and ninty (9 0) days on labor with the following provisions: 1.