Table of Contents
Advertisement
Quick Links
Operating instructions
1592.8216- 14
Ident-Nr.:
01316143
These instructions contain fundamental information and precautionary notes. Please
read the manual thoroughly before installing or operating the unit. These instructions
must always be used in conjunction with the operating instructions of the mixer and any
other supplementary operating instructions concerning the mixer itself or its compo-
nents.
This instruction manual contains fundamental information about the installation and
operation of the mixer accessories. The responsibility for ensuring the observation of all
regulations in force at the place of installation - also by any temporary labour assisting
with the installation work - lies with the user. Accessories must only be used in accor-
dance with their designated purpose on the KSB mixer they are intended for. It is not per-
mitted to use them on any other mixers, whether these be of KSB or any other make.
Amamix -
Mounting / Fixing Instructions
Installation Parts / Accessories
direct
Advertisement
Table of Contents
Related Manuals for KSB Amamix
Summary of Contents for KSB Amamix
- Page 1 - lies with the user. Accessories must only be used in accor- dance with their designated purpose on the KSB mixer they are intended for. It is not per- mitted to use them on any other mixers, whether these be of KSB or any other make.
- Page 2 Amamix - direct Table of Contents Page Pre - conditions for Installation General Checking the Site before Installation Checking the Parts before Installation Preparations for Installation Transporting the Mixer Installing the Mixer on the Support Foot Installing the Mixer on the Reservoir Floor...
-
Page 3: Pre - Conditions For Installation
Amamix - direct Pre - conditions for Installation More specifically, non - compliance may, for example, result in: Failure of essential mixer and/or plant functions; Health hazard due to electrical shock, mechanical impact, General chemical contamination. - Safety Pollution of the environment by the leakage of This operating manual contains basic instructions, which must be hazardous substances. -
Page 4: Preparations For Installation
Amamix - direct Preparations for Installation Transporting the Mixer Only use the suspension device (lifting clamp with shackle) for transporting the mixer. Do not damage the propeller blades or the electrical power cable during transport (support the weight of the cable in an adequate manner). -
Page 5: Fixing The Dead - Ending The Electrical Power Cable
Amamix - direct Fixing the Dead - ending the Electrical Power Cable Lead the power cable to the wall of the reservoir, to cross arms or similar, and pull it tight by means of a cable grip as follows: pull the cable grip over the cable end and pull the... - Page 6 Amamix - direct Standard Accessories - Set No. 6 For permanent mounting of the mixer on the tank floor ( Amamix direct 215, 300, 400) Sling point ∅ Retaining clamp Pedestal ∅ Min. dimensions for installation through tank cover opening (jet direction 0...
-
Page 7: Standard Installation Accessories
Amamix - direct Standard Installation Accessories Installing Mixer Mast It is very important that the mixer mast assembly be properly installed. Each assembly must be plumb in both directions and secured to the tank wall and floor with the supplied anchor bolts. -
Page 8: Installing The Guide Rail Retaining Bracket
45 lbf - ft Hmin Mounting the Claw to the Mixer Screw the claw to the motor casing cover of the mixer using four hexagon head bolts. Tightening torques: Amamix 215/300: 13 lbf - ft Amamix 400/500/600: 45 lbf - ft... - Page 9 Amamix - direct NOTE: The dimension is from the bottom of the sump to the Hmin center line of the propeller. Center support of guide pipe Size Hmin (inches) 4 15/16 5 15/16 Amamix Amamix 12 5/8 16 9/16...
-
Page 10: Lifting The Mixer Out Of The Reservoir
Amamix - direct Lifting the Mixer out of the Reservoir (e.g. for maintenance) Unscrew the connecting bolts M 10 between the adjustment strap and the bearing part and turn the direction of the jet back to its centre position (90_ - position, symmetry of the adjustment strap relative to the bearing part) by means of square M 27 or the mounting lever. - Page 11 â Amamix - - direct KSB INC 4415 SARELLEN ROAD, RICHMOND, VA 23231 Tel. (804) 222-1818S Fax (804) 226-6961S www.ksb-inc.com...