Precaution - You must keep the car key taken off from the car while you work this and finally, connect power of the interface. - When to connect the interface cable, you must keep the power cable taken off. - You must work this at the environment without any static electricity or damages.
- PIP (picture in picture) Function (Only available in 8.8” model) - Higher Quality - Controlling PIP function, switching AV source by steering wheel buttons. - Easier operation with new remote control. - Upgraded OSD Menu - Displaying External AV sources through composite, RGB - Controlling AV sources (DVD, Navi) by I-DRV –...
Main Spec. 1. Input Spec. (MULTI VIDEO INTERFACE) -. 1 x Analog R,G,B (Sync on Green) -. 1 x CVBS(REAR CAMERA) Input. (Rear camera source) - 3 x A/V (NTST & PAL) Input. -. 1 x LCD Input (Car system Input) 2.
System Composition Switch for source toggle Remote (OSD keypad) OEM Navi Button (Can Interface) NAVIGATION Input (Analog RGB) Car installation OEM DISPLAY A/V 1 A/V 2 VIDEO CIRCUIT A/V 3 VIDEO MUX CVBS In (Rear camera) Car Screen Input POWER A/V OUT (CAR MAIN BOARD) FMTX...
Connector Pin Assignment A/V (IN/OUT) RGB(IN) MODE POWER *Power Connect *RGB-IN Connect ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ② ③ ⑥ ① ④ ⑤ ⑦ ① ACC (RED) ① R DATA (RED) *12V Select ② GND (BLACK) ②...
Page 12
ON : Skipping A/V 3 A/V 3 MUTE OFF : A/V3 Display ON : 6.5” LCD Setting (Possible to use BMW 1 series) To select monitor size OFF : 8.8” LCD Setting ON : Siemens setting (only when to turn on the 5...
Page 13
E60 Siemens 6.5” New 3 Series in 2009 ※DIP S/W Use Example [E60 Alpine 6.5”] [BMW E60-6.5” Alpine] -. Use Input Mode : A/V3(DVD), Navigation (RGB) -. Rear Camera : When to be installed on CVBS 4 ▷ DIP S/W : 1 ▷...
How to use Remote Dimension : 85 * 40 * 8 (mm) POWER : Interface operation PIP : Short press – Activating PIP (Picture in Picture) Long press – Switching AV source MENU : Activating OSD Menu OK : Select ▲...
-OSD(On Screen Display) · Analog RGB Mode · Video Mode IMAGE Menu - BRIGHTNESS - CONTRAST -SHARPNESS - SATURATION -HUE -USER IMAGE -15-...
Page 16
OSD(On Screen Display) · Analog RGB Mode · Video Mode OSD Menu -LANGUAGE : (Only available for English) TRANSPARENT -H_POSITION : Move the position of AV sources to Left, Right -V_POSITION : Move the position of AV sources to Up, Down -16-...
OSD(On Screen Display) · Analog RGB Mode · Video Mode UTIL Menu FACTORY RESET : Initializing of all values of OSD setting (Impossible to reset of screen position, only possible for functions in OSD) -17-...
OSD(On Screen Display) · Factory Mode ▲ → ▼ → ▲ →MENU buttons of the remote. - Factory mode is activated by pressing Factory Mode - PARK – PARK ENABLE - H-POSITION - V-POSITION - UTIL – CAR MODEL : Selection of using this interface for E60, E70. - FACTORY RESET : Initializing -18-...
How to use parking guide line Factory Default : DISPLAY - DISABLE ① When the car gear is in reverse, ① Enter to the Factory mode by ▲ → ▼ → ▲ →MENU button of remote. Then, the left image will be displayed on the screen.
Page 20
How to use parking guide line ③ ③ Can move the line with H-Position on the factory mode. ④ ④ Can move the line with V-Position on the factory mode. -20-...
CAN Wiring & Steering wheel button ☆ : PIP Mode : Switching AV source with long press Orange+Black: CAN HIGH Yellow: CAN LOW * The colors of wires could be Different by car models. -21-...
Product Composition Remote : 1 EA Ground Cable : 1 EA LCD (F-TYPE) Cable : 1 EA Navi Cable : 1 EA Power Cable : 1 EA Toggle Switch : 1 EA (Optional) A/V Cable : 1 EA -22-...
Installation manual Factory CAN wires Control Box Backside of Factory LCD wire monitor Connector LCD-IN LCD-OUT DIP S/W KEYPAD PIP-BMW-STD 노 흰 란 색 색 POWER/CAN MODE RGB(IN) A/V(IN/OUT) AV3-SEL AV2-SEL AV1-SEL NAVI SEL CAN(L) ※ Wiring CAN High (White) of the interface...
Page 24
-FAQ 1. When can not change mode. -. Check if the IR Cable (Remote) is connected or not. -. Check if LED is turned on or not. If it is not turned on, Check if power cable is connected or not. -.
Page 25
I-DRV type Selection. Update Date : 10 .Dec.2008 * You can select I-DRV type by Factory Menu of OSD. In the Factory menu, please select UTIL I_DRIVE Menu. Then, you can choose I-DRV type to OLD I-DRV or NEW I-DRV considering your car.
Need help?
Do you have a question about the PIP and is the answer not in the manual?
Questions and answers