Page 2
Wireless Remote Control...................17 Remote Control Operation Guide..............18 Bluetooth Pairing ..........20 (Replacement Remote Control) ® Remote Control Emergency Power Down Feature..........22 Troubleshooting....................23 Warranty......................25 Warranty Information: Please see the warranty that came with your product. Reverie 7T Power Base CUSTOMER SERVICE: 800-973-8374 CUSTOMERSERVICE@REVERIE.COM...
To disconnect, turn all controls to the off position, then remove plug from outlet. • Do not place remote in water or area of intense heat. • Do not lift bed by wooden side rails. • Excessive dropping of the remote may cause performance issues. CUSTOMER SERVICE: 800-973-8374 CUSTOMERSERVICE@REVERIE.COM...
Page 4
Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. CUSTOMER SERVICE: 800-973-8374 CUSTOMERSERVICE@REVERIE.COM...
Page 5
Your power base is strictly designed for in-home use only. It is NOT designed for hospital use and is NOT designed to meet hospital standards. Do not use this base with TENT TYPE oxygen therapy equipment or near explosive gases. CUSTOMER SERVICE: 800-973-8374 CUSTOMERSERVICE@REVERIE.COM...
Page 6
(3Amp). When there is a short-circuit, a fuse on the transformer will be blown in order to protect the electrical equipment (Fuse: 1.5A). Should the above situation occur, the customer should seek professional assistance by calling a licensed electrician or by contacting customer service at 800-973-8374. CUSTOMER SERVICE: 800-973-8374 CUSTOMERSERVICE@REVERIE.COM...
Page 7
This Product is not designed to support or lift 850 lbs of total weight in the head or foot sections of your Reverie 7T power base alone, or in any unevenly distributed fashion. Some mattresses are not designed for Power Bases because they do not bend or flex well when adjusted.
Page 8
DO NOT SIT ON THE HEAD OR FOOT SECTIONS WHILE IN THE RAISED POSITION. INTENDED USAGE The electric power base should be installed with the head board brackets and/or the head of the frame positioned close to a wall. CUSTOMER SERVICE: 800-973-8374 CUSTOMERSERVICE@REVERIE.COM...
Page 9
Parts List for Reverie 7T Power Base Note: Before discarding any packing materials, check the power base carton and verify the following items in the parts list are included: PARTS LIST Wireless Remote Control (1) Mattress Retainer Bracket (2) Base Legs (4)
· Loosen cam lock at both corners. · Loosen and remove hardware [bolts/nuts] from the two inside slide brackets of each rail. [see figure 1A,1B, and 1C] · Gently detach the head and foot rails. Figure 1D Figure 1A Figure 1E CUSTOMER SERVICE: 800-973-8374 CUSTOMERSERVICE@REVERIE.COM...
Page 11
Briefly activate all functions on the wireless WARNING: remote control to verify that all of the features are operational. If your Reverie 7T Power POWER CORDS MUST NOT INTERFERE Base does NOT operate, please refer to the WITH ANY POWER BASE MECHANISMS.
Page 12
3 inches (76.2 mm). STEP 10 Install the headboard brackets to the power base. Place one bracket on the left-hand side of the power base and one bracket on the right-hand side of the power base. CUSTOMER SERVICE: 800-973-8374 CUSTOMERSERVICE@REVERIE.COM...
Page 13
Bracket (E) and into Inner Headboard Bracket (D). Use a 5/16 Inch Washer (J) and 5/16 Inch Typical Reverie 7T Power Base is now Locking Nut (K) and hand tighten to allow complete. If the power base is equipped with for adjustment.
App User Guide How to Download Your Reverie 7T Power Base has a Bluetooth Accessory Module as standard equipment. the App Software STEP 1 Please use any of the previously listed devices to log into the APP Store. STEP 2 Type “Reverie Remote”...
Page 15
Your position readout on a scale of 1-100 will appear at the top of the screen and next to the head or foot position. • NOTE: Lumbar control is not available on the 7T adjustable power base. Massage • Control your massage intensity and duration.
Page 16
Shows nearby beds that you can connect to in order of proximity. • Help – Contact info for technical support. • Mattress Configurator – Reconfigure your Reverie Dream or Dream Supreme mattress with these firmness guides. • Factory Reset – Reset your app to original settings.
H. MASSAGE WAVE PATTERN PRESET I. INCREASE(+) & REDUCE(-) MASSAGE INTENSITY ON HEAD SECTION OF THE BASE J. INCREASE(+) & REDUCE(-) MASSAGE INTENSITY ON FOOT SECTION OF THE BASE K. STOP ALL MASSAGE FEATURES L. MICRO USB CHARGING PORT CUSTOMER SERVICE: 800-973-8374 CUSTOMERSERVICE@REVERIE.COM...
Memory button continuous use. for more than 5 seconds until the LED light flashes 3 times to signal Memory position is stored. • To recall a Memory Position: Press 1 of the 4 presets. CUSTOMER SERVICE: 800-973-8374 CUSTOMERSERVICE@REVERIE.COM...
Page 19
FEATURES: When there is a short circuit, a fuse on the transformer will be blown in order to protect the electrical equipment (Fuse: 1.5A). • The Reverie 7T power base uses a Bluetooth remote control system. ® • The included remote is already paired with...
Page 20
STEP 6 If you choose OTHER then you will be shown a list of all beds available and asked if you would like to PAIR MULTIPLE BEDS. If yes, scroll and select beds to pair. CUSTOMER SERVICE: 800-973-8374 CUSTOMERSERVICE@REVERIE.COM...
Page 21
Press the “Zero G” button within the B.T menu to identify the bed. The foundation’s night light and PLC light will activate and the Note: Dot indicates selected bed. massage will turn on for 2 seconds and cut off Note: Dot indicates selected bed CUSTOMER SERVICE: 800-973-8374 CUSTOMERSERVICE@REVERIE.COM...
Remote Control Emergency Power Down Feature Your Reverie 7T power base has an STEP 3 emergency lowering feature in the event that Press the “FLAT” button (C) or the individual your power base is in the raised position and lower buttons (A,B) to lower the power base to has lost power due to a power outage.
Troubleshooting In the Event the Reverie 7T Power Base fails to operate, investigate the symptoms and possible solutions provided in the chart below: Symptom Solution • Verify the power cord is plugged into a working, grounded electrical outlet. A Remote Control appears to be operable but will grounded, electrical surge protection not activate the bed.
Page 24
• If the Reverie 7T is installed over a bed frame, verify the massage motors are not causing the bed frame (or bed frame components) to vibrate.
Purchaser. This four (4) year Limited Warranty shall not apply if Purchaser does not return any and all defective parts to Reverie within 15 days of Purchaser’s receipt of replacement part. Purchaser shall bear all service, transportation, labor and shipping costs related to the delivery and/or replacement of the defective part.
Page 26
Upon receiving reasonable written notice at any point in time that is more than five (5) years and up to twenty (20) years from the warranty commencement date, Reverie will offer replacement parts for any mechanical part of the frame found to be defective. Electronics, electrical components, drive motors and massage motors are excluded from this Limited Warranty.
Page 27
Warranty UNLESS OTHERWISE EXPRESSLY STATED IN THIS DOCUMENT, REVERIE AND THEIR RESPECTIVE PARENTS, SUBSIDIARIES, DIVISIONS AND AFFILIATES EXPRESSLY DISCLAIM ANY OTHER WARRANTY WHATSOEVER, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND FREEDOM FROM DEFECTS AND WORKMANSHIP.
Bed Serial Number__________________________________________________________ Email Address_____________________________________________________________ To register your warranty via mail, send this portion and a copy of your proof of purchase (invoice or sales receipt) to: Reverie Warranty Dept. 314 Central Ave. Silver Creek, NY 14136 (800-973-8374) CUSTOMER SERVICE: 800-973-8374 CUSTOMERSERVICE@REVERIE.COM...
Need help?
Do you have a question about the 7T and is the answer not in the manual?
Questions and answers
How do I set the nightlight on the remote for the 7T power base?