Advertisement
Quick Links
STAGE-4 ROKKER
XXR
®
Custom 630w 4-Speaker/
Amplifier Install Kit for
2014-2018 Harley
®
StreetGlide/Ultra
XXRK-630SP4-14SG-ST4
#
Installation
Instructions
Warning:
The speakers provided in this kit have an impedance of 2-ohms. They are designed for use with
the 2006-2010 Harley Harmon Kardon audio system ONLY. Use of these 2-ohm speakers on the 1998-2005
Harley audio system can and will cause permanent damage to the system.
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for J&M Corporation XXRK-630SP4-14SG-ST4
Summary of Contents for J&M Corporation XXRK-630SP4-14SG-ST4
- Page 1 Custom 630w 4-Speaker/ Amplifier Install Kit for 2014-2018 Harley ® StreetGlide/Ultra XXRK-630SP4-14SG-ST4 Installation Instructions Warning: The speakers provided in this kit have an impedance of 2-ohms. They are designed for use with the 2006-2010 Harley Harmon Kardon audio system ONLY. Use of these 2-ohm speakers on the 1998-2005...
- Page 2 Product Overview Fig. A This is the new J&M STAGE-4 ROKKER® XXR Custom 630w 4-speak- er/amplifier installation kit for your 2014-2018 Harley StreetGlide with the Harley BoomBox 6.5GT Premium or 4.3 standard radio. At the very heart of this system is our in-fairing mounted 4 channel ROKKER XXRP amplifier rated @ 157.5w RMS per channel X 4 to provide up to 630w total RMS power! The amplifier will be custom tuned for use in conjunction with your...
- Page 3 8. Unplug the speaker wires from the speaker and set aside. Fig. C 9. Remove the stock grill from the inner fairing by removing the 3 attachment screws. VERY IMPORTANT: Discard these screws as they will not be used again. (Figure D) 10.
- Page 4 Saddlebag-Lid Speaker Installation 1. Remove the windshield, outer fairing shell, vent below windshield, fuel tank and seat. 2. From the top of the saddlebag lid, remove the 4 screws securing the speaker and as you remove the stock Harley speaker from the lid, unplug the wire connection at the bottom of the speaker.
- Page 5 4. Position the speaker down into the lid to determine if the 3” hole needs to be enlarged slightly in any direc- tion, to completely clear the ROKKER XX speaker magnet. A Dremel tool with rotating bit can be used to enlarge this opening.
- Page 6 7. Mark the second of three 9/64th” holes to be drilled, drill the hole and then insert the 6-32 X ½” Allen head screw, with washer, up thru the bottom of the basket, thru the cup and secure using the supplied nut plate.
- Page 7 Amplifier Installation Fig. A 1. Remove the windshield, outer fairing shell, vent below windshield, fuel tank and seat. 2. Remove and replace the stock metal tray above the radio with the J&M Amplifier mounting tray by removing the 4 screws holding the tray to the radio, 4 screws holding the tray to the speaker enclosures, and 2 screws holding the tray to the gauge assembly.
-
Page 8: Specifications
Fig. C Power Harness Speaker Speaker Enclosure Enclosure Amplifier 2-Pin Connectors Orange Fig. D 2-Pin 4-Pin Remote Connectors Turn On Connector 2-Pin 12v Amp Turn On Connector Left Speaker Right Speaker Lower Fairing Speakers or Rear Speakers Specifications ROKKER® XXRP 630 Full Range Class D Amplifier S/NRatio Separation... - Page 9 WARRANTY AND REPAIR INFORMATION TWO YEAR LIMITED WARRANTY In order to facilitate the servicing of this warranty, the Warranty Registration Form should be filled out and returned within 10 days of the date of purchase. However, return of the Warranty Registration Form is not a precondition of this warranty, and this Warranty will be observed by J&M CORPORATION whether or not the Warranty Registration Form is returned, on the condition that other satisfactory evidence of the date of the original purchase is provided to J&M CORPORATION.
Need help?
Do you have a question about the XXRK-630SP4-14SG-ST4 and is the answer not in the manual?
Questions and answers