Advertisement
Quick Links
Advertisement
Related Manuals for A4Tech R4
Summary of Contents for A4Tech R4
- Page 1 X7 Oscar Wireless Gaming Mouse Model: R4 www.a4tech.com...
- Page 2 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Federal Communications Commission Requirements The equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to part 15 of the FCC Rules.
-
Page 3: Hardware Installation
(Otherwise, installation is failed and you have to remove the software and re-install.) To remove the software, follow the below steps: Go to START>> PROGRAMS >>A4TECH Software >> "X7 Oscar Mouse Editor" >> "Uninstall X7 Oscar Mouse Editor", see figure on the right. - Page 4 X7 Oscar Mouse Editor Mode Name/Select: Mode Number: Name a new mode or select Select a mode number to edit. modes to use. Mouse Button Definition: Description of Reminder: Display current mouse button settings or Enter short description here for each setup new settings to mouse buttons.
- Page 5 Button Settings and Relevant Functions Click any “button definition area” on the main menu; you will see the function listing as shown below. According to your preference, you may select one of them as the button setting. You also can enter a short description on the “Description of reminder”...
- Page 6 Memo See below "Memo" section in more details. One click to open the Memo screen and list out all the current button settings as the reminder. You may setup any of mouse buttons of 2, 3, 4, 5, 6, wheel up(UP) and wheel down(DN) with "Memo"...
- Page 7 this gesture function is only available for mouse button and . See more details on the Gesture 16-in-1 section. Screen Shot Button / / can be set as "Screen Shot". One click to take a screenshot of a chosen area of the screen or video and quickly share with others. Screenshot Usage Configure your screenshot button: 1.
- Page 8 DPI Levels & Color Indicator Suitable Resolution of display DPI Levels (Default) Indicator Color Recommended for: （ （ （ （ Recommended） ） ） ） DPI 1: 400DPI No light 800×600 Slow-Speed and normal accuracy player DPI 2: 800DPI Green 1024×768 Medium-Speed and average accuracy required player DPI 3: 1,200DPI...
- Page 9 The “Gesture 16-in-1” offers customizable 16 functions in 1 click with gesture button. You may setup 16 most-frequently-used commands to the Gesture buttons from 6 categories, more than 30 commands, including Keyboard, Mouse, Hyperlink, Office, Text, Multimedia, Internet and Key Setting Reminder.
- Page 10 3. Click “ ” to save to receiver’s memory. 4. Draw the line in Excel. Original After drawing the line, the column has been enlarged Draw the line in Windows Picture and Fax Viewer Original After drawing the line, the column has been enlarged Task Listing of X7 Oscar Mouse Editor There are 2 ways will display the working mode number when it is shifted: Display 1: When the mode is shifted, the memo screen will be displayed on the screen center to remind current...
- Page 11 Auto Launch on Boot : If this task is selected, X7 Oscar Mouse Editor will be auto-executed when the system boots up. Mouse-Control Panel : Select “Mouse-Control Panel” will open “Mouse Properties” setup screen of your Windows system, e.g., you may setup mouse pointers and other often -used mouse settings.
- Page 12 Check Battery power: Click "Check Power" in "power-saving management" to check the battery power status. Low Battery Inform: When the mouse power is low, Low Battery Inform page will pop up at the right corner of your screen to remind you to replace the batteries in time.
- Page 13 Note: The red-colored of Multi-link receiver is also available with single gift box. It is back compatible and supports A4Tech's G3, G5, G7 and G10 series, making them reunion as a family. Note that functions of multiple buttons will be restricted for those limited buttons of some back models. And Multi-link function does not applicable to G6 series.
- Page 14 Press any key to wake up the mouse before “ID pairing” is performed. >>Locate the power switch (Normally you can find it on the mouse bottom side). >> Make sure the power switch is in OFF position and then switch it to ON position within 30 seconds. (If power switch is in ON position, switch it to OFF and back to ON position within 30 seconds).
- Page 15 Step 1: Launch the "Macro Manager"(Open the Oscar Mouse Editor >> Select "Macro Manager" from the task pull-down menu of the designated button) Step 2: Knowing the instructions of “Macro Manager” . Keyboard Simulation Area . Mouse Simulation Area . Record Button When you want to record your settings, click on "...
- Page 16 Step 1: Click on "Play Macro Once Only" of the "Macro Manager Menu" >>Select "Play Macro Repeatedly" >> Select "Press to start, Release to stop" as shown right. Step 2: Tick the box of "Perform delay each time a key is pressed" >>Select "mSec"...
- Page 17 Step 1: Tick the box of the "Perform delay each time a key is pressed" and "Perform delay each time a key is released" at "Macro Manager Menu">> Select "mSec" of time unit in the "Time unit". Step 2: Input "64" of time value in "Time" box. >>Click "Left" on "Mouse Simulation Area".
- Page 18 Step 1: Click on "Play Macro Once Only" at the "Macro Manager Menu" >>Select "Play Macro Repeatedly">>Select "Press to start, Release to stop". Step 2: Tick the box of "Perform delay each time a key is released" >>Select "mSec" of time unit in the "Time unit".
- Page 19 Step 1: Input "799" of coordinate value in "Mouse Relative Coordinate X Axis Box" of the "Macro Manager Menu">>Click "Plug In". Step 2: Select "mSec" of time unit in the "Time unit" >> Input "23" of time value in "Time" box. >>Click "Plug In". Step 3: Repeat three times from step 2 to step 3.
-
Page 20: Troubleshooting
Notice To ensure that your mouse sends and receives perfectly, please read below instructions for your reference: 1. Avoid Channel Confliction from Auto Channel Hopping 2). Select "Channel-lock" to define a private channel to secure better 1). Left-click on the icon " "... -
Page 21: Product Support
Product Support Need help with technical support? Please go to: http://www.a4tech.com/ennew/support.asp and our support team will respond within 72 hours. **All pictures and description mentioned above is for reference only and is subject to change without notice.