Profile California 400MSX Installation And Owner's Manual

Profile California 400MSX Installation And Owner's Manual

Mosfet power amplifiers

Advertisement

MOSFET POWER AMPLIFIERS
Installation Instructions / Owner's Manual
400MSX
600MSX

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the California 400MSX and is the answer not in the manual?

Questions and answers

Summary of Contents for Profile California 400MSX

  • Page 1 MOSFET POWER AMPLIFIERS Installation Instructions / Owner's Manual 400MSX 600MSX...
  • Page 2 It is recommended that you have our product installed by an authorized Profile retailer. However, if you decide to install it yourself, please carefully read through this manual and take your time to do a quality installation.
  • Page 3: Safety Precautions

    AFETY PRECAUTIONS Fuse amplifier's power wire at the battery. Be sure to fuse the power wire within 12" of the car's battery. This will protect the car's battery in case of a short circuit between the power amplifier and battery. THIS IS A MUST, the amplifier's built-in fuse will only protect the power amplifier not the car's battery! Use high grade wire connectors.
  • Page 4: Features And Benefits

    EATURES AND BENEFITS DC Offset Protection This circuit protects the output of the amplifier against DC voltage. If for some reason DC voltage is detected at the output stage, the amplifier will shut down protecting the speakers from direct current. Short Circuit Protection The circuit protects the amplifier from damage due to a short found in the speakers or wiring.
  • Page 5: Remote Turn-On

    Power Fusing This protects the amplifier against short circuits and excessive current. Remote Turn-on Automatically turns amplifier on when connected to the head unit's remote output. The amplifier will turn on and off with the head unit to save current consumption. This control also operates the reset circuit for the amplifier's protection.
  • Page 6: Mounting Location

    OUNTING LOCATION Before you start the installation, it will be necessary to find a mounting location for the amplifier. Find a location in which the amplifier will receive adequate ventilation in order to dissipate the heat it develops during operation. Two popular mounting locations are in the trunk or under the seat.
  • Page 7: Power Connections

    OWER CONNECTIONS Speaker Output Fuse RADIO'S REMOTE RADIO'S REMOTE TURN-ON OUTPUT TURN-ON OUTPUT 94.7 94.7 IMPORTANT! Before making any connections, disconnect the car's battery until the installation is completed to avoid possible damage to the electrical system. Connect the amplifier to the car's battery. At times, the amplifier will need to draw large levels of current that cannot be provided by any circuit in the car's fuse box.
  • Page 8: Signal Connections

    IGNAL CONNECTIONS Connect the output of the head unit (AM/FM cassette player, CD, or DAT) to the RCA input terminals of the amplifier. To make these connections, we recommend high quality RCA cables, which are available at your local car audio retailer. Run signal wires away from electrical wires to avoid possibility of induced noise from the car's electrical system (i.e.
  • Page 9 IGH LEVEL CONNECTIONS (OPTIONAL) If a low level RCA signal source is not available, you may still wire the amplifier with high-level or speaker level outputs from your head unit. ground" system may be used (see diagram below). Use the provided plug to make the following connections .
  • Page 10: Speaker Connections

    PEAKER CONNECTIONS Make the speaker connections using speaker wire that is at least 10 gauge or heavier. As with any audio component, proper phasing of the amplifier and speakers is essential for strong bass response. When connecting, make sure that positive (+) from the amplifier is connected to the positive (+) of the speaker, and the same for negative (-).
  • Page 11 ETTING THE CROSSOVER AND BASS BOOST Select your crossover type and frequency. The amplifier is equipped with a built-in variable low -pass crossover network allowing you to select the desired crossover point for your subwoofers. manufactures recommended crossover point. X-over Select the crossover point for your speakers.
  • Page 12: Troubleshooting The System

    ROUBLE SHOOTING THE SYSTEM We have put together this trouble-shooting guide if you experience problems after installing the amplifier. Please keep in mind that the majority of problems incurred are caused by improper installation and not the equipment itself. In addition, there are many components in the system that could cause various signal problems such as inducted electrical noise and engine noise.
  • Page 13: Specifications

    PECIFICATIONS Max Power @ 4 Ohm RMS Power @ 4 Ohm Max Power @ 2 Ohm RMS Power @ 2 Ohm THD @ RMS Power Frequency Response Signal To Noise RCA Input Sensitivity RCA Input Impedance High Level Input Impedance Load Impedance Crossover Type (12dB/Octave) Crossover Frequency (Variable)
  • Page 14: Limited Warranty

    One (1) Year from the date of sale to the original consumer purchaser. If this product is proven to be defective within this one year period, Profile will repair it when said product is returned, with a copy of the dated sales receipt, freight prepaid to Profile.
  • Page 15 4) Include a brief description of the problem or failure with the unit. 5) Include the return street address and daytime telephone number. 6) Allow 2~3 weeks for repair (this period includes shipping time). Send unit to : PROFILE CONSUMER ELECTRONICS, INC. 15060 SHOEMAKER AVE SANTA FE SPRINGS, CA 90670 TEL: (562)404-9393...
  • Page 16 PROFILE CONSUMER ELECTRONICS, INC. 15060 SHOEMAKER AVE SANTA FE SPRINGS, CA 90670 TEL: (562)404-9393 FAX: (562)404-9433 WWW.PROFILEUSA.COM...

This manual is also suitable for:

California 600msx

Table of Contents