1. Manuals
  2. Brands
  3. Marksman Manuals
  4. Car Alarm
  5. M5A
  6. Installation manual

Marksman M5A Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Installation
Manual
Model: M5a
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference; and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to
this equipment. Such modifications could void the user's authority to operate the equipment.
For Technical Assistance, please call (800) 638-3600,
or visit www.magnadyne.com

Advertisement

Table of Contents
loading

Related Manuals for Marksman M5A

Summary of Contents for Marksman M5A

  • Page 1 Installation Manual Model: M5a This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2) This device must accept any interference received, including interference that may cause undesired operation.
  • Page 2 Index Step 1: Component Installation ..........2 Step 2: 10-Pin Main Harness Installation .

  • Page 3: Step 2: 10-Pin Main Harness Installation

    Step 2: 10-Pin Main Harness Installation First Vacant Socket: (For Use with ALA-RPT Relay Pack Only) See Optional Accessory Connection for proper wiring. Gray Wire: (Pulsed Ground for Car Horn) Connect the gray wire to the negative trigger wire on the vehicle’s horn relay. Warning! Maximum output of this wire is 300mA.

  • Page 4: Step 3: 5-Pin Power Harness Installation

    Step 3: 5-Pin Power Harness Installation The power harness contains 3 wires and two vacant sockets. Follow the wiring recommendations enclosed for each wire. Power Harness First Socket Second Socket First Vacant Socket: The first vacant wire socket is a low current (300mA) grounded output wire that can be used to activate the vehicle’s interior lighting system when the security system is disarmed.
  • Page 5 Step 4: Optional Accessory Connections (continued) 3 Wire Ground Trigger Door Lock System Black 3-Pin Plug Black Wire: Connect to Unlock Orange Wire: No Connection To Alarm Lock Control Red Wire: Connect to Lock Switch ( - ) Lock Out Ground Input To Door Lock Control Relays...
  • Page 6 Step 4: Optional Accessory Connections (continued) Newly Installed Power Door Lock Motors Red Wire: Lock Orange Wire: To +12 Volts Violet Wire To +12 Volts Black Wire: Unlock (Battery +) Black 3-Pin Plug White Wire Brown Wire To Ground ALA-DL1 Relay Pack Green Wire: Lock To Newly...
  • Page 7 Step 4: Optional Accessory Connections (continued) Unlock Driver's Door First Wiring for 3-Wire Positive Door Lock System Red Wire Orange Wire Black Wire To +12 Volts (Battery +) Driver's To Power Door Door Lock Motor Lock Switch Lock/Unlock Unlock + Unlock Wires Unlock Driver's Door First Wiring for 5-Wire Ground at Rest Door Locking Systems Red Wire...
  • Page 8 Step 4: Optional Accessory Connections (continued) Starter Disable Wiring: Using the wiring information and diagram below, connect the optional starter disable relay as follows: A. Locate the “Start Only Wire” coming from the ignition key switch and cut it. B. Connect the ends of the cut start wire the black wires coming from the ALA-RPS relay pack. C.
  • Page 9 Step 4: Optional Accessory Connections (continued) Flashing Lights Headlight Switch Piggyback Selectable + or – Parking Connection Red Wire with White Stripe Lights Output from Alarm Only Valet/Override Switch with Blue 2-Pin Plug Alarm Status LED Indicator with White 2-Pin Plug: Plug the white 2-pin plug into white receptacle located in the side of the control module.
  • Page 10 Step 4: Optional Accessory Connections (continued) Dual-Zone Electronic Sensor Plug Red Wire: +12 Volt Sensor Power Supply Black Wire: Sensor Ground Supply Blue Wire: Sensor Alarm Trigger Input Green Wire: Sensor Pre-Warning Input (for Dual-Zone Sensors Only) White 4-Pin Plug Red 4-Pin Plug Optional Dome Light Illumination and Lighted Pathway Illumination Purple Wire...

  • Page 11: Step 4: Optional Accessory Connections

    Step 4: Optional Accessory Connections (continued) Dome Light Supervision Using Optional ALA-RPT Relay Pack: Insert Black Wire into the First Socket Insert Red Wire into the Second Socket Orange Wire Output to Dome Light (+ or -) ALA-RPT Purple Wire Black Wire Relay Pack Input to Relay (+ or -)

  • Page 12: Step 5: Transmitter Coding

    Step 5: Transmitter Coding Remote Transmitter Coding and Operation: Dedicated Buttons The supplied transmitters are pre-programmed to the security system alarm module using Dedicated Buttons Mode. Follow the procedures below to add replacement transmitters or to change from Dedicated Buttons Mode to Separate Channel Mode. Step 1 Step 2 Turn On the Ignition Key...

  • Page 13: Step 5: Transmitter Coding

    Step 5: Transmitter Coding (continued) Step 2 Step 1 Turn On the Ignition Key Flip Valet Switch On/Off 4 Times The horn/siren will Chirp 2 time and the LED indicator will be on solid. This indicates the module is ready for Separate Channel Button Mode. Step 6 Step 3 Step 4...
  • Page 14 Step 6: Remote Feature Programming (Part 1) Step 2 Step 1 “Dedicated Button Mode” “Separate Channel Mode” Make Sure the Security System is Disarmed Turn On the Ignition Key Step 3 Flip the Valet Switch On/Off 6 Times The LED will be on solid. The horn/siren will emit 6 short beeps.
  • Page 15 Step 5 Turn Off the Ignition The LED will be Off and the horn/siren will emit 1 short beep and 1 long beep. You are now out of the feature programming mode. Step 6: Remote Feature Programming (Part 2) Step 2 Step 1 Flip the Valet Switch On/Off 8 Times Turn On the Ignition Key...

  • Page 16: Step 6: Remote Feature Programming

    Step 6: Remote Feature Programming (Part 3) Step 2 Step 1 Turn On the Ignition Key Flip the Valet Switch On/Off 10 Times The LED will be on solid. The horn/siren will emit 10 short chirps to indicate you are now in Part 3 “Remote Feature Programming”...

  • Page 17: Step 8: General Testing

    Step 8: General Testing (Alarm Function) To test the basic functions of the alarm system repeat the following procedures: 1. Turn Off the ignition key and exit the vehicle closing all protected entrances. 2. Press the LOCK button on the transmitter. You will hear a siren/horn chirp, the parking lights will flash one time and the LED status indicator will flash at normal speed.
  • Page 18 Step 9: Speciality Feature and Optional Equipment Testing Starter Disable: 1. Enter the vehicle and close all the entrances. 2. Arm the alarm using the transmitter. 3. Turn the ignition key to the start position. The engine will not crank over. 4.

  • Page 19: Step 9: Speciality Feature And Optional Equipment Testing

    Step 9: Speciality Feature and Optional Equipment Testing RF Tamper Rearm: Note: This feature is activated automatically when the alarm is programmed for automatic arming (See “Remote Feature Programming” on page 14-15). 1. Alarm must be programmed for automatic arming. 2.

  • Page 20: Wiring Diagram

    Violet Wire Positive Door Pin Trigger Input Vacant Socket (Optional Channel #2, see page 11) Red Wire with White Stripe Parking Lights Relay Output (Selectable + or -) Pink Wire Parking Lights Relay Input © Copyright 2004 Magnadyne Corporation M5A-IM 2-10-04 Rev. B...

Table of Contents