Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Polargos SIMPLE MOVE 102
Summary of Contents for Polargos SIMPLE MOVE 102
- Page 1 SIMPLE MOVE Installation and operation guide...
- Page 2 2.7 Obstacle detection - 3-button remote control 5.3 Deleting a remote control 6 Troubleshooting 6.1 Support 6.2 Replacing the remote control battery 6.3 Deleting of settings 6.4 Diagnostics 7 Technical specifi cations EN – Installation and operation guide SIMPLE MOVE 102...
- Page 3 Installation, adjustment and maintenance of the drive unit must be performed by a professional mechanical devices and home automation installation engineer. EN – Installation and operation guide SIMPLE MOVE 102 EN – Installation and operation guide SIMPLE MOVE 102...
-
Page 4: Electrical Installation
4. Laying conductors Polargos will not be liable for any damages resulting from failure to follow the Cables laid underground must be equipped with a protective sheath with a suffi cient instructions in this guide. - Page 5 Do not use the drive unit if it needs repairing or adjusting. Gates in poor condition must 7. Safety instructions regarding operation be repaired, reinforced or even replaced aſt er prior approval of the POLARGOS technical department. WARNING Use only original parts for any maintenance or repair work.
- Page 6 Detection and removal of the obstacle. 11. Regulations POLARGOS hereby confi rms that this product conforms to the basic requirements and other relevant provisions of Directive 1999/5/CE. This Declaration of Conformity can be viewed at www.polargos.pl This product is approved for use in the European Union and Switzerland.
- Page 7 If this is not the case, mark the sections that are placed excessively high and are invisible. h > 5 mm EN – Installation and operation guide SIMPLE MOVE 102 EN – Installation and operation guide SIMPLE MOVE 102...
-
Page 8: Product Description
Flat washers 10.5x22x2, Orange light* Opening stop* galvanized Antenna* Drive Double-thread screw Safety edge* Toothed bar 10x15 mm Photocells* *optional accessories Pin 10x60 S12 EN – Installation and operation guide SIMPLE MOVE 102 EN – Installation and operation guide SIMPLE MOVE 102... - Page 9 – the electronic foundations control system is on standby Flashing see diagnostics page 32 Laying of cables EN – Installation and operation guide SIMPLE MOVE 102 EN – Installation and operation guide SIMPLE MOVE 102...
-
Page 10: Dimensions
To connect several accessories to the START terminal, a cable with a 0.3 mm² cross section may be used (example: telephone cable) instead of a cable with a cross section of 0.75 mm². EN – Installation and operation guide SIMPLE MOVE 102 EN – Installation and operation guide SIMPLE MOVE 102... -
Page 11: Tools Required For Assembly (Not Provided)
4 nuts (M10, galvanized). Insert the cable grommet that has been drilled through in the hole provided for the supply cable. EN – Installation and operation guide SIMPLE MOVE 102 EN – Installation and operation guide SIMPLE MOVE 102... -
Page 12: Assembly
Fasten the subsequent bars and toothed bars as shown above. Once the bars are fastened, check whether everything is level or not; if not, correct this. EN – Installation and operation guide SIMPLE MOVE 102 EN – Installation and operation guide SIMPLE MOVE 102... -
Page 13: Mechanical Adjustment
View from inside View from inside Do not connect any cable to terminal M2. Never lock the drive when the gate is in motion. EN – Installation and operation guide SIMPLE MOVE 102 EN – Installation and operation guide SIMPLE MOVE 102... -
Page 14: Connecting To The 230 V Power Supply
4 and a star washer using a screw Tighten the supplied cable clamp. For a 3x1.5 mm² cable For a 3x2.5 mm² cable EN – Installation and operation guide SIMPLE MOVE 102 EN – Installation and operation guide SIMPLE MOVE 102... -
Page 15: Gate Track Self-Learning
During the self-learning process, pressing button 1 on the remote control or the button on the electronic control system stops the gate and the self-learning process. EN – Installation and operation guide SIMPLE MOVE 102 EN – Installation and operation guide SIMPLE MOVE 102... -
Page 16: Complete Opening And Closing Of The Gate
10 W - 24 V bulb MAXIMUM – The use of a bulb with power greater than 10 W- 24 V can cause the drive unit to malfunction.. ▶ Operation of the orange light The orange light fl ashes while the gate is moving. EN – Installation and operation guide SIMPLE MOVE 102 EN – Installation and operation guide SIMPLE MOVE 102... -
Page 17: Battery (Optional)
Connect the antenna to the electronic module terminals 1 and 2 (blue label „ANT”): • cable core to terminal 1 • earthing strap to terminal 2 EN – Installation and operation guide SIMPLE MOVE 102 EN – Installation and operation guide SIMPLE MOVE 102... -
Page 18: Advanced Parameter Settings
The indicator light comes on then goes out. Opening for pedestrian entry is deactivated on this button. EN – Installation and operation guide SIMPLE MOVE 102 EN – Installation and operation guide SIMPLE MOVE 102... -
Page 19: Automatic Closing
fl ashes; Automatic closing press button 1 on the is activated. remote control 3 times. EN – Installation and operation guide SIMPLE MOVE 102 EN – Installation and operation guide SIMPLE MOVE 102... -
Page 20: Setting Slow Speed
The indicator light P1 goes out for 5 light P1 is off . Standard speed The indicator seconds, and then fl ashes. is selected. light P1 fl ashes. EN – Installation and operation guide SIMPLE MOVE 102 EN – Installation and operation guide SIMPLE MOVE 102... -
Page 21: Programming The Remote Controls
Possibility 2 Other Somfy RTS device Complete opening The 3-button remote control cannot be used to change the drive settings. EN – Installation and operation guide SIMPLE MOVE 102 EN – Installation and operation guide SIMPLE MOVE 102... -
Page 22: Adding A Remote Control
The remote control has been saved in the comes on. memory. 5.3 Deleting a remote control See “Deleting of settings” page 42. EN – Installation and operation guide SIMPLE MOVE 102 EN – Installation and operation guide SIMPLE MOVE 102... -
Page 23: Troubleshooting
Short circuit within Check the cables of the drive unit *Gate track, deactivation of the settings. the drive unit (see page 29). EN – Installation and operation guide SIMPLE MOVE 102 EN – Installation and operation guide SIMPLE MOVE 102... -
Page 24: Technical Data
• Emergency battery input • Photocell input • Dry contact control input Yes (does not work with solar power or a battery) EN – Installation and operation guide SIMPLE MOVE 102 EN – Installation and operation guide SIMPLE MOVE 102... - Page 25 POLARGOS SP. Z O.O. ul. Deptak 17, 04-956 Warszawa Tel.: +48 22 872 00 91– 93 www.polargos.pl...
Need help?
Do you have a question about the SIMPLE MOVE 102 and is the answer not in the manual?
Questions and answers