How do I program my GE universal remote using codes?

To program your GE universal remote using codes, follow these steps:Locate the Code List that came with your remote. Find the section for the type of device you want to control (e.g., b-ray, dvr, tv, cbl, amp, aux) and circle all the remote codes for your device's brand.Press and hold the SETUP button on the remote until the red light turns on, then release it. The red light will remain on.Press and release the device button on the remote for the type of device you want to control (e.g., b-ray, dvr, tv, cbl, amp, aux). The red light will blink once and remain on.Use the number buttons on the remote to enter the first 4-digit remote code you circled in the Code List. The red light will turn off after entering the fourth digit.Point the remote at the device and test the buttons to see if it responds as expected. If the buttons do not operate the device, return to Step 2 and use the next code you circled for that device.

Why is my GE universal remote not working?

If your GE universal remote is not operating your device, consider the following:Ensure the batteries are fresh and installed correctly.Aim the remote directly at your device, and make sure there are no obstructions between them.Make sure you have selected the appropriate device on the remote (e.g., TV for TV, CBL for cable box).Try programming the remote with a different code.The remote may not be compatible with your device. For more information, see page 14 of the manual.

How do I reset my GE universal remote?

To reset your GE universal remote to factory settings, follow these steps:Press and hold down the SETUP button on the remote until the red light turns on. Release the SETUP button. The red light will remain on.Press and release the MUTE button.Press and release the number #0 button. The red indicator light will flash twice. For more information, see page 13 of the manual.

How do I program my GE universal remote to a TV?

To program your GE universal remote to a TV, use the Direct Code Entry method:Locate the Code List included with your remote. Find the section for the tv device type and circle all remote codes for your TV's brand.Press and hold the SETUP button on the remote until the red light turns on, then release it. The red light will remain on.Press and release the tv device button on the remote. The red light will blink once and remain on.Use the number buttons on the remote to enter the first 4-digit remote code you circled in the Code List. The red light will turn off after entering the fourth digit.Point the remote at the TV and test the buttons to see if it responds as expected. If the buttons do not operate the device, return to Step 2 and use the next code you circled for that device.

What steps should I take if a programming code does not work for my device?

If a programming code does not work for your device, or if it only operates a few functions, you should:Try programming the remote with a different code from the Code List for more functionality.If no remote code works or there are no codes in the Code List for your device, use the Auto Code Search method to program your remote.For combination devices (e.g., TV/DVD combo), you may need to enter a code for each device part.

Why did my GE universal remote suddenly stop working?

If your remote stops operating properly, you should replace the batteries with new ones.

How do I switch between different devices after programming my GE 24922 Universal Remote?

To switch between different devices after programming, simply press the corresponding device button on the remote, such as b-ray (dvd), dvr, tv, cbl (sat), amp, or aux. This selects the device you wish to control. For more information, see page 5 of the manual.

Is the GE 24922 Universal Remote compatible with smart TVs or streaming sticks?

Yes, the remote can be programmed to control Streaming Media Players using any of the device buttons. Additionally, the Guide button provides easy access to features on today's streaming devices.

How do I reprogram my GE universal remote?

You can reprogram your GE universal remote using two methods: Direct Code Entry or Auto Code Search. Direct Code Entry (Recommended):Locate the Code List included with your remote. Find the section for your device type and circle all remote codes for the brand.Press and hold the SETUP button until the red light turns on, then release it.Press and release the device button for the type of device you want to control (e.g., tv). The red light will blink once and remain on.Use the number buttons to enter the first 4-digit remote code you circled. The red light will turn off after the fourth digit.Point the remote at the device and test the buttons. If they do not operate the device, repeat the process with the next code.Auto Code Search: Manually turn on the device you want to control. Press and hold the SETUP button until the red light turns on, then release it. Press and release the device button for the type of device you want to control (e.g., tv). The red light will blink once and remain on. With the remote pointed at the device, press and release the POWER button. The remote will send 10 different codes. The red light will blink once for each code and remain on after sending them. If the device turns off, proceed to Step If not, repeat this step to test the next 10 codes. Manually turn the device back on. With the remote pointed at the device, press and release the VOL+ button. The remote will re-send the first code of the 10 codes from Step The red light will blink once and remain on. If the device turns off, press and release the same device button you pressed in Step 3 to store the code. If not, continue to press and release the VOL+ button until the device turns off. Be sure to wait approximately 3 seconds after each press. Once the device turns off, press and release the same device button you pressed in Step 3 to store the code. Test the remote buttons to ensure the device responds as expected. If not, return to Step 2 and repeat the process to search for a better code.

How do I program my GE universal remote for a DVD player?

To program your GE universal remote for a DVD player, use the Direct Code Entry method:Locate the Code List included with your remote. Find the section for the b-ray (which includes DVD) device type and circle all remote codes for your DVD player's brand.Press and hold the SETUP button on the remote until the red light turns on, then release it. The red light will remain on.Press and release the b-ray device button on the remote. The red light will blink once and remain on.Use the number buttons on the remote to enter the first 4-digit remote code you circled in the Code List. The red light will turn off after entering the fourth digit.Point the remote at the DVD player and test the buttons to see if it responds as expected. If the buttons do not operate the device, return to Step 2 and use the next code you circled for that device.

How do I exit programming mode on my GE 24922 Universal Remote?

When using the Direct Code Entry method, the red light will turn off after entering the fourth digit of the code, indicating the programming process is complete. In the Auto Code Search method, once a code is successfully stored by pressing the device button, the programming process is complete.

How can I reset my GE universal remote without a code?

To reset your GE universal remote to factory settings, follow these steps:Press and hold down the SETUP button on the remote until the red light turns on. Release the SETUP button. The red light will remain on.Press and release the MUTE button.Press and release the number #0 button. The red indicator light will flash twice. For more information, see page 13 of the manual.

What type of batteries does the GE 24922 Universal Remote require?

Your universal remote requires two (2) AAA batteries (not included). Alkaline batteries are recommended. For more information, see page 3 of the manual.

What should I do if my GE universal remote's light is not lighting up?

If your GE universal remote is not operating your device, which may include the light not lighting up, you should make sure the batteries are fresh and installed correctly.