Advertisement
Quick Links
#788 Wooden Doll High Chair
IMPORTANT! This file contains the assembly instructions for two different versions of this item.
Please refer to the table below to determine which instructions match your item, and on which
pages you can find them.
Version A
pages 2-7
FEATURE
One-piece seat back with integrated legs (versus separate seat back and rear legs)
Assembly Instructions
Version B
pages 8-15
A B
X
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Melissa & Doug 788
Summary of Contents for Melissa & Doug 788
- Page 1 #788 Wooden Doll High Chair Assembly Instructions IMPORTANT! This file contains the assembly instructions for two different versions of this item. Please refer to the table below to determine which instructions match your item, and on which pages you can find them.
- Page 2 #788 Wooden Doll High Chair Assembly Instructions © 2006 Melissa & Doug, Inc. All Rights Reserved...
- Page 3 High chair assembly components Seat back Front leg assembly Chair arms quantity = 1 quantity = 1 quantity = 2 (left & right) Chair seat Tray quantity = 1 quantity = 1 Spindles with fittings Regular spindles quantity = 2 quantity = 2 Hardware (not to scale) 1 1/4 “...
- Page 4 Step 1: Take the seat piece and bolt it into the front leg assembly piece. Make sure the two tabs are facing downward on the seat and the arch with the heart is towards the bottom on the front leg assembly. You want to use two bolts (one at a time) and screw them in from the top of the seat.
- Page 5 Step 3: Take the two spindles with fittings and bolt them into the front leg assembly (one at a time). These two spindles should be bolted into the holes located on the back, at the very bottom of the front leg assembly. When bolting the spindles on, make sure to hold them steady. Do not turn the spindles to help tighten the bolts, turn the bolts only.
- Page 6 Step 5: Take the back piece and line up the dowels on the seat and the arms with the holes on the back piece. Push the dowels into place so that the back piece sort of locks into place. Then line up the spindles with the holes on the back piece.
- Page 7 Note: This is what your high chair should look like once all the steps are completed. Page 6 of 6...
- Page 8 #788 Wooden Doll High Chair Assembly Instructions © Melissa & Doug, Inc. Version B All Rights Reserved...
- Page 9 High chair assembly components left arm rest quantity = 1 front leg assembly quantity = 1 seat back quantity = 1 right arm rest quantity = 1 seat quantity = 1 long leg spindle quantity = 2 rear legs quantity = 1 tray quantity = 1 short leg spindle...
- Page 10 Step 1: Attach the front leg assembly to the bottom front of the seat with two screws from the top of seat. Secure the screws with the Allen wrench. screws seat front leg assembly completed assembly Page 3 of 8...
- Page 11 Step 2: Attach the left and right arm rests to the top of the seat by attaching a screw through the bottom of the seat into the bottom front of each arm rest. It may be easier to turn the chair assembly upside down when tightening each screw. Make sure to insert the wooden dowel in the bottom of each arm rest into the corresponding hole in the top of seat before fully tightening the screw.
- Page 12 Step 3: Attach a long leg spindle to each of the front legs by inserting a screw through the front of each leg into the end of each spindle. Hand tighten the screws only. They need to remain loose to complete the assembly. You will fully tighten the two screws in a later step.
- Page 13 Step 4: Attach the seat back to the assembly by aligning the dowels on each arm rest with the holes in the seat back. At the same time, insert the dowels in the back of the seat with the holes near the bottom edge of the seat back. With all 4 dowel inserted, secure the seat back with two screws, one into each arm rest.
- Page 14 Step 5: Insert the two short leg spindles into the holes in the front legs. Attach the rear legs to the assembly by inserting the two dowels on the seat back into the holes at the top of the rear legs. Carefully align the four loose spindles with the large holes on the lower part of the rear legs.
- Page 15 Step 6: Attach the tray by sliding it into the slots on the inside surfaces of each arm rest. tray front of tray has rounded bottom completed assembly Page 8 of 8...
Need help?
Do you have a question about the 788 and is the answer not in the manual?
Questions and answers