RIDGID NaviTrack Operator's Manual

Seesnake cs10 10 watt pipe and cable line transmitter
Hide thumbs Also See for NaviTrack:

Advertisement

NaviTrack
Pipe and Cable Line Transmitter
WARNING!
Read this Operator's Man-
ual carefully before using
this tool. Failure to under-
stand and follow the con-
tents of this manual may
result in electrical shock,
fire and/or serious person-
al injury.
Operator's Manual
®
NaviTrack Line Transmitter
Serial
No.
10 Watt
Record product serial number below as it appears on the nameplate.
Original Instructions – English – 1

Advertisement

Table of Contents
loading

Summary of Contents for RIDGID NaviTrack

  • Page 1 Read this Operator’s Man- ual carefully before using this tool. Failure to under- stand and follow the con- NaviTrack Line Transmitter tents of this manual may result in electrical shock, Record product serial number below as it appears on the nameplate.
  • Page 2 Components ��������������������������������������������������������������������������������������������������������������������������������������������������������������������5 Icon Legend ���������������������������������������������������������������������������������������������������������������������������������������������������������������������6 Pre-Operation Inspection ������������������������������������������������������������������������������������������������������������������������������������������������6 Work Area and Equipment Set Up High Voltage Warning ��������������������������������������������������������������������������������������������������������������������������������������������������� 7 Powering the NaviTrack Line Transmitter ���������������������������������������������������������������������������������������������������������������������� 7 Operating Instructions Direct Connect Mode ����������������������������������������������������������������������������������������������������������������������������������������������������8 Inductive Clamp Mode ������������������������������������������������������������������������������������������������������������������������������������������������ 10 Inductive Mode ����������������������������������������������������������������������������������������������������������������������������������������������������������� 10 Air‑Coupling �����������������������������������������������������������������������������������������������������������������������������������������������������������������11...
  • Page 3: General Safety Rules

    Safety Symbols In this operator’s manual and on the product, safety symbols and signal words are used to communicate important safety information� This section is provided to improve understanding of these signal words and symbols� This is the safety alert symbol� It is used to alert you to potential personal injury hazards� Obey all safety messages that follow this symbol to avoid possible injury or death�...
  • Page 4: Specific Safety Information

    Pre‑ ventive safety measures reduce the risk of injury� This section contains important safety information that is specific to the NaviTrack Line Transmitter. Read these • Store idle equipment out of the reach of children and...
  • Page 5: Description, Specifications, And Standard Equipment

    NOTE: The NaviTrack Line Transmitter complies with Part ground line can be traced� Use the NaviTrack Line Trans‑ 15 of FCC rules in accordance with the following: Operation mitter in conjunction with a RIDGID‑SeekTech locator or a...
  • Page 6: Work Area And Equipment Set Up

    Manual for more information) Battery Status ‑ Hold Power Key down for two seconds to check battery status Set up the NaviTrack Line Transmitter and work area in accordance with these procedures to reduce the risk of Inductive Mode ‑ Press frequency key...
  • Page 7: High Voltage Warning

    3� Inspect the line to have a signal applied to it� The line before opening the battery compartment. To prevent over- must be metal to allow the NaviTrack Line Transmitter heating and leakage, do not mix battery types or used and to locate it�...
  • Page 8: Operating Instructions

    Direct Connect Mode Battery Level Indicator To check the battery level, turn ON the NaviTrack Line Trans‑ Direct Connect Mode is most commonly used when the tar‑ mitter, hold down the Power Key until all the LEDs light get utility is readily accessible� Do not use Direct Connect up, and then release the Power Key �...
  • Page 9 The LED will blink rapidly Conductor three times when set� The 262 kHz LED will blink every 5 seconds to indicate that the NaviTrack Line Transmitter is operating on the alternate 200 kHz frequency� 8� Check the circuit� More current will give a stronger sig‑...
  • Page 10: Inductive Clamp Mode

    1� Place the NaviTrack Line Transmitter so the orientation mark located on top of the NaviTrack Line Transmitter aligns with the target conductor� 2� Place the NaviTrack Line Transmitter over the line to be traced (See Figure 12)� Figure 11 – Inductive Clamp...
  • Page 11 Sounds in Inductive Mode 3� If required, rotate the NaviTrack Line Transmitter on the conductor’s axis to help reduce the chance of air cou‑ The NaviTrack Line Transmitter emits two beeps when shift‑ pling (See Figure 13)� ing into Inductive Mode� When operating in Inductive Mode, the NaviTrack Line Transmitter emits a series of intermittent four‑tone beeps�...
  • Page 12: Helpful Hints

    The LED over the new power current selected will flash rapidly� NOTE: If the NaviTrack Line Transmitter reports low or no current by emitting a low beep rate, the signal may be too low to be detected by the receiver locator and inadequate for tracing.
  • Page 13: Cleaning

    Service and repair of the NaviTrack Line Transmitter must be performed by a RIDGID Independent Authorized Service Do not use liquid or abrasive cleaners on the NaviTrack Line Center� Transmitter� Do not use solvents to clean any part of the NaviTrack Line Transmitter�...
  • Page 14: Troubleshooting

    Check that the transmitter is in the correct mode� See the descriptions for Direct Connect Mode, Inductive Clamp Mode, and Inductive Mode� Check that the receiver and the NaviTrack Line Transmitter are set to the same Receiver will not pick up the NaviTrack frequency (for example, some receivers will use 93,622�9 Hz or 93,696 Hz...
  • Page 15 NOTES English – 15...
  • Page 16: Lifetime Warranty

    RIDGE TOOL COMPANY. RIDGID reserves the right to change the specifications of the hardware, software, or both as described in this manual without notice. Visit www.seesnake.com for current updates and supplemental information pertaining to this product.

Table of Contents