Hide thumbs Also See for XP-SP30:

Advertisement

SERVICE MANUAL
Ver 1.1 2003. 10
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wavelength: λ = 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW (This output is the value
measured at a distance of 200 mm from the objective lens
surface on the optical pick-up block with 7 mm aperture.)
Power requirements
For the area code of the model you purchased, check the
upper left side of the bar code on the package.
• Two LR6 (size AA) batteries: 1.5 V DC × 2
• AC power adaptor (DC IN 4.5 V jack):
US, Canadian models: 120 V, 60 Hz
AEP model: 100 - 240 V, 50/60 Hz
• Two Ni-MH rechargeable batteries (size AA):
1.2 V DC × 2
Sony Corporation
9-961-141-02
2003J16-1
Personal Audio Company
© 2003.10
Published by Sony Engineering Corporation
XP-SP30
Model Name Using Similar Mechanism XP-ZV71
CD Mechanism Type
Optical Pick-up Name

SPECIFICATIONS

Dimensions (w/h/d) (without projecting
parts and controls)
Approx. 133 × 34 × 151 mm (5
Mass (excluding accessories)
Approx. 333 g (11.7 oz)
Operating temperature
5°C - 35°C (41°F - 95°F)
Supplied accessories
Headphones (1)
Hand strap (1)
AC power adaptor* (1)
* Not supplied with the U model. For the area code of the
model you purchased, check the upper left side of the
bar code on the package.
Design and specifications are subject to change without
notice.
US Model
Canadian Model
AEP Model
CDM-3325ER
DAX-25E
× 1
× 6 in.)
1
3
/
/
4
8
PORTABLE CD PLAYER

Advertisement

Table of Contents
loading

Summary of Contents for Aiwa XP-SP30

  • Page 1: Specifications

    XP-SP30 SERVICE MANUAL US Model Canadian Model Ver 1.1 2003. 10 AEP Model Model Name Using Similar Mechanism XP-ZV71 CD Mechanism Type CDM-3325ER Optical Pick-up Name DAX-25E SPECIFICATIONS System Dimensions (w/h/d) (without projecting parts and controls) Compact disc digital audio system Approx.
  • Page 2 XP-SP30 TABLE OF CONTENTS This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. 1. SERVICING NOTE ·························································· 3 2. GENERAL ·········································································· 5 3. DISASSEMBLY 3-1. CABINET (UPPER) SUB ASSY, PANEL (UPPER) LID ASSY ········································...
  • Page 3 XP-SP30 SECTION 1 SERVICING NOTE BEFORE REPLACING THE OPTICAL PICK-UP BLOCK NOTES ON HANDLING THE OPTICAL PICK-UP Please be sure to check thoroughly the parameters as par the “Optical BLOCK OR BASE UNIT Pick-Up Block Checking Procedures” (Part No.: 9-960-027-11) issued separately before replacing the optical pick-up block.
  • Page 4 XP-SP30 TEST MODE The software version display and LCD test can be performed when the test mode is activated. Procedure: 1. Confirm the set is not powered on. (Remove two batteries and disconnect the AC power adaptor.) 2. Short the solder land SL301 (TEST) on the MAIN board.
  • Page 5: General

    XP-SP30 SECTION 2 GENERAL This section is extracted from instruction manual. 1 s(stop)/CHARGE 3 r/t (skip/search) 2 ca* (play/pause)/ENTER 4 SOUND \ (headphones) jack 5 PLAY MODE/ (repeat) OPEN/LOCK knob DC IN 4.5 V (external power input) jack 6 VOLUME +*/–...
  • Page 6: Panel (Upper) Lid Assy

    XP-SP30 SECTION 3 DISASSEMBLY Note : Disassemble the unit in the order as shown below. CABINET (UPPER) SUB ASSY, PANEL (UPPER) LID ASSY CD MECHANISM CONTROL BOARD (CDM-3325ER) MOTOR ASSY (SLED) (M902), MAIN BOARD OPTICAL PICK-UP (DAX-25E), TURN TABLE MOTOR ASSY (SPINDLE) (M901) Note : Follow the disassembly procedure in the numerical order given.
  • Page 7 XP-SP30 3-2. CONTROL BOARD 1 eleven screws 3 plate (control) two hooks 4 CONTROL board 3-3. CD MECHANISM (CDM-3325ER) three insulators CD mechanism (CDM-3325ER ) connector (2P) flexible board (CN403) (15P) (CN401) connector (4P) (CN402)
  • Page 8: Optical Pick-Up (Dax-25E

    XP-SP30 3-4. MAIN BOARD 1 battery terminal (-) 3 MAIN board When installing it, align the switch position as shown. 2 battery terminal (+) S304 3-5. MOTOR ASSY (SLED)(M902), OPTICAL PICK-UP (DAX-25E), TURN TABLE MOTOR ASSY (SPINDLE)(M901) 1 three screws (B1.7x4)
  • Page 9: Electrical Checking

    XP-SP30 SECTION 4 ELECTRICAL CHECKING The CD section adjustments are done automatically in this set. RF Level Check In case of operation check, confirm that RF level. Condition: • Hold the set in horizontal state. Precautions for Check Perform check in the order given.
  • Page 10 XP-SP30 SECTION 5 DIAGRAMS NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS Note on Printed Wiring Board Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or • X : parts extracted from the component side.
  • Page 11 XP-SP30 5-1. BLOCK DIAGRAM OPTICAL PICK-UP BLOCK IC402 (DAX-25E) DSP,DSSP,DAC, IC701 DRAM CONTROLLER HEADPHONE AMP VCC2 J701 AOUT1 LOUT RFAC ROUT RFDC AOUT2 LRMU MUTE BEEP IC403 PWRSW 4M BIT DRAM Q207 IC201(1/2) VCC1 XTAI IC301 MOTOR/COIL DRIVER X401 SYSTEM CONTROLLER 16.934MHz...
  • Page 12: Main Board (Side A)

    XP-SP30 5-2. PRINTED WIRING BOARDS – MAIN BOARD (SIDE A) – • : Uses unleaded solder. NOT USED MAIN BOARD (SIDE A) SL701 TJ302 TJ301 SL303 R316 CN302 TP304 R304 TP301 TJ303 C314 TJ305 TP306 S303 (OPEN/CLOSE) C312 TJ306 TJ304...
  • Page 13: Main Board (Side B)

    XP-SP30 5-3. PRINTED WIRING BOARDS – MAIN BOARD (SIDE B) – • : Uses unleaded solder. MAIN BOARD (SIDE B) OPTICAL PICK-UP BLOCK (DAX-25E) C322 R339 TAP304 CONTROL BOARD R341 CN301 (Page 17) R706 R722 C707 C702 R705 M902 R721...
  • Page 14 XP-SP30 5-4. SCHEMATIC DIAGRAMS – MAIN BOARD (1/3) – • See page 10 for Waveforms. • See page 20 for IC Block Diagrams. R720 C423 C424 C422 R435 6.3V C431 C434 2.2k C425 C429 TP433 47 6.3V L402 L404 R436...
  • Page 15 XP-SP30 5-5. SCHEMATIC DIAGRAMS – MAIN BOARD (2/3) – • See page 10 for Waveforms. • See page 19 for IC Block Diagrams. L211 C229 C232 L208 6.3V D206 R211 MA111-TX R215 100k Q202 R216 2SB1237TV2PQR 100k Q201 2SD1781K-T146-QR R227...
  • Page 16 XP-SP30 Ver 1.1 2003.10 5-6. SCHEMATIC DIAGRAMS – MAIN BOARD (3/3) – • See page 10 for Waveforms. • See page 20 for IC Block Diagrams. R708 R715 R716 TP703 C715 FB701 R752 TJ711 C705 C707 C717 R717 J701 C709 0.47...
  • Page 17: Control Board

    XP-SP30 5-7. PRINTED WIRING BOARDS – CONTROL BOARD – • : Uses unleaded solder. CONTROL BOARD MAIN BOARD CN301 (Page 13) LCD001 LIQUID CRYSTAL DISPLAY VOLUME PLAY MODE/ SOUND 1-689-411- (11)
  • Page 18: Control Board

    XP-SP30 5-8. SCHEMATIC DIAGRAMS – CONTROL BOARD – LCD001 LIQUID CRYSTAL DISPLAY 2.2k 2.2k 2.2k 2.2k KEY2 2.2k 2.2k 2.2k 2.2k VCPU KEY1...
  • Page 19: Ic Block Diagrams

    XP-SP30 5-9. IC BLOCK DIAGRAMS IC201 BH6580KV 52 51 48 47 44 43 DCIN HV PROT H BRIDGE H BRIDGE H BRIDGE 40 LATCH LEVEL CONTROLLER 39 DATA SHIFT INTERFACE 38 CLOCK 37 WAKEUP REGB 36 XRST RESET 35 RESET_0...
  • Page 20 XP-SP30 IC402 CXD3048R AVDD MIRR DIGITAL ASYMMETRY DFCT ANALOG SW VSSI CORRECTOR TEST TEST TES1 TEST1 AVDD2 AVDD VSS2 AOUT2 FRDR FOCUS VREFR FFDR DIGITAL AVSS2 TRDR TRACKING ERROR AVSS1 TFDR CORRECTOR VREFL SRDR SLED AOUT1 SFDR AVDD1 AVDD SSTP...
  • Page 21: Ic Pin Function Description

    XP-SP30 5-10. IC PIN FUNCTION DESCRIPTION • IC301 T5AW5-4RR7 (SYSTEM CONTROLLER) Pin No. Pin Name Description — Ground terminal (digital) System clock input from CXD3048R(IC402) XOUT Not used (open) TEST Test pin (normally connected to ground) VDD1 — Power supply terminal (digital +2V)
  • Page 22 XP-SP30 Pin No. Pin Name Description FG_I FG pulse signal input from BH6580KV(IC201) PGMSEL_O Not used PWRSW_O Power supply control output of TA2120FN(IC701) (“H”:ON) XPOWLT_O Latch signal output to BH6580KV(IC201) CHGGND_SL_I Not used (connected to ground) XOPSTBY_O Optical-pick up voltage control output (“H”:gain up) OPGSW_O RF AMP gain control output (“H”:gain up)
  • Page 23: Exploded Views

    XP-SP30 Ver 1.1 2003.10 SECTION 6 EXPLODED VIEWS NOTE: • -XX, -X mean standardized parts, so they may • The mechanical parts with no reference number The components identified by mark 0 or have some differences from the original one.
  • Page 24 XP-SP30 Ver 1.1 2003.10 6-2. CABINET (LOWER) SECTION supplied supplied supplied supplied supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-256-548-31 PANEL (LOWER)(US) 3-254-082-11 SCREW 3-256-548-41 PANEL (LOWER)(CND) X-3383-837-1 LOCK ASSY, OPEN X-3383-874-1 KEY (OPEN) ASSY...
  • Page 25: Cd Mechanism Section (Cdm-3325Er)

    XP-SP30 6-3. CD MECHANISM SECTION (CDM-3325ER) M901 M902 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-318-203-61 SCREW (B1.7X4), TAPPING 3-221-475-01 SHAFT, STANDARD 0 102 X-3380-950-1 OPTICAL PICK-UP (DAX-25E) 3-222-298-01 RACK 3-221-473-01 COVER, GEAR 3-222-299-01 SPRING, RACK RETAINER 3-221-472-02 CHASSIS 3-348-998-31 SCREW (M1.4X2.5), TAPPING, PAN...
  • Page 26: Electrical Parts List

    XP-SP30 Ver 1.1 2003.10 SECTION 7 CONTROL MAIN ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • RESISTORS • SEMICONDUCTORS In each case, u: µ, for example: parts list may be different from the parts All resistors are in ohms.
  • Page 27 XP-SP30 MAIN Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C316 1-162-968-11 CERAMIC CHIP 0.0047uF 10% C722 1-162-915-11 CERAMIC CHIP 10PF 0.5PF C750 1-162-962-11 CERAMIC CHIP 470PF C317 1-107-826-11 CERAMIC CHIP 0.1uF 10.00% 16V C751 1-162-962-11 CERAMIC CHIP...
  • Page 28 XP-SP30 Ver 1.1 2003.10 MAIN Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks L213 1-216-295-91 SHORT CHIP R320 1-216-864-11 METAL CHIP 1/16W L214 1-469-570-11 INDUCTOR 10uH R321 1-216-833-11 METAL CHIP 1/16W L215 1-469-570-11 INDUCTOR 10uH R322...
  • Page 29 XP-SP30 Ver 1.1 2003.10 MAIN Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R706 1-216-833-11 METAL CHIP 1/16W MISCELLANEOUS (AEP) *************** R706 1-216-837-11 METAL CHIP 1/16W 1-827-461-11 CABLE, FLEXIBLE FLAT (26P) 0 102 (US, CND) X-3380-950-1 OPTICAL PICK-UP (DAX-25E)
  • Page 30 XP-SP30 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2003.08...

Table of Contents