Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for ZEPCAM T2
Summary of Contents for ZEPCAM T2
- Page 1 T2 BOD Y C A M I N ST RU CTI ON MANUAL EN 1.0...
- Page 2 WE LCO M E! Thanks for buying a ZEPCAM T2 camera. We hope you will enjoy our product as much as we enjoyed creating it. Before starting please check: - If the product or the packaging is not visibly damaged.
- Page 3 • User management and add users D o c ki ng station • Product descriptions • Pairing the docking station to the Zepcam Manager • Offloading and charging with the T2 docking station. T 2 p rob lem solv i ng...
- Page 5 • The Zepcam T2 is a bodycam for professional use to record video, audio and GPS. The T2 camera is very easy to use, ruggedized and has a large battery to record up to 7 hours continously. The Zepcam T2 comes with an integrated back end solution to store and manage recorded footage.
- Page 6 TAKE A PICTURE WHILE RECORDING • When pre-recording is activated, indicator 9 is flashing red. PRERECORDING (you can activate this option in Zepcam Connect). ENABLED • Press once for reset (no data and settings will be lost). RESET • Long / short beep every 10 seconds...
- Page 7 C O LO U R SIGN AL S Green light : Device powered ON in standby mode Not recording Red light : Recording video Red light : One flash - a picture is taken Green light : Blinking- with one beep - storage full Red and green light : Battery empty single beep...
- Page 8 The single docking station is used to charge and offload data using a PC or laptop with Zepcam Connect software installed. • Your Zepcam T2 must be connected by a USB cable to a PC or a laptop with Zepcam Connect installed.
- Page 9 1. Run the Setup file to install Zepcam Connect (provided by your Zepcam contact person). 2. When Zepcam Connect is newly installed and started for the first time it will ask for the unlock/pairing code: Choose between: unlock software or unlock software and pair to server...
- Page 10 • Please follow these steps in case you want to use Zepcam cloud or server for storage and video management. Pairing Zepcam Connect with Cloud or Zepcam Server 1. First, log in to Zepcam Manager (cloud s1.zepcam.com s4.zepcam.com server software) and follow the steps below.
- Page 11 5. A pop up appears with Connect Code: 6. Copy Connect Code and send to the person that needs to activate Zepcam Connect 7. In Zepcam Connect: enter activation / pairing code at screen. 8. In Zepcam Connect: message “Pairing successful”.
- Page 12 2. If this is the first time the T2 is connected with Zepcam Connect, the program will ask you to enter the PIN: XXXXX [NOTE] The PIN has been supplied together with the Zepcam T2 (in the box). The program will remember this PIN to authenticate the camera automatically in the future.
- Page 13 S O FTWA R E O P TI O NS When accessing “Preferences” for the first time, you will be asked to create a Zepcam Connect Admin password (password prevents end users adjusting T2 settings). Pay attention to put a password you will remember. You will need it to make changes on your Zepcam T2 camera.
- Page 14 [Note] In most cases, the default settings are suitable T2 Device Manager When you entered the wrong pin for a T2, you can change it and enter the correct PIN for the T2 in this window (don’t forget to Save!).
- Page 15 Server Settings: • If you only unlocked Zepcam Connect, optionally you are also able to pair the Zepcam Connect with the Zepcam Cloud or a Zepcam server by selecting the Server Settings tab and enter the pairing code. • Shows the pairing status, which server Zepcam Connect is paired with and under which name this Zepcam Connect is known in the cloud or on the Zepcam Server;...
- Page 17 • Zepcam Manager is the software to manage Zepcam devices, users and store and manage recorded video, audio and GPS data. Zepcam Manager is avalaible as Cloud solution (hosted and managed by Zepcam ) and Server Software (installed on the IT network of the client).
- Page 18 In this section, find how to: Add users to Zepcam Manager Pairing Zepcam Connect with Cloud or Zepcam Server Give users access to view specific camera and camera recordings There are 2 user levels within the Zepcam Manager: User: Admin: •...
- Page 19 Provide users with login details Give Users access to view camera (and its recordings) in Zepcam Manager [Note] This action is only possible after the T2 camera offloaded images or videos for the first time into the cloud or Zepcam Server.
- Page 21 • The Zepcam T2 docking station makes recharging of T2 bodycams and data offload easy, secure and fast. Video data from T2 bodycams is transferred to the docking station and from the docking station offloaded to the server or cloud using an Ethernet cable.
- Page 22 (offloaded and (check error list) fully charged) Link indicator: Red: Link with Zepcam Cloud or Zepcam Server software Not red: No link Pulsing red: Offloading to Zepcam Cloud or Zepcam Server. Docking station status: Green flash: Docking station starting up...
- Page 23 6. Use a browser to log in on the IP address of the docking station. 7. Click on the blue button ‘Server Pairing’...
- Page 24 8. Now, within your browser open a new tab and login Zepcam Manager (Cloud or Server Software). You need to login with admin rights to add a new docking station and create a pairing code. 9. Go to Settings -> Devices -> Docking Stations...
- Page 25 When status LED is solid red, the docking station is started up and ready for use and there is link with Zepcam Cloud or Zepcam Server. 12. The docking station should now be paired with server and ready for offloading.
- Page 26 6. If the right T2 LED indicator is off the T2 is being fast charged (the T2 is switched off during fast charging). 7. If the left T2 indicator is off and the LED in front of the camera is green, the T2 is ready for use (offloaded and fully charged).
- Page 27 If the Zepcam T2 behaves oddly, or does not respond to button presses: 1. Reset the T2 by pressing the right button on the back of the camera 2. On the docking station, when the LED in front of the camera is Flashing Green/Red, an Error occurred and user interaction is needed.